The Yamaha AN1x Synthesizer mailing list

Hi Guys,

I can't get any sound nor MIDI when I hit the lowest C.
Do you have any idea if it is a DIY job to fix?

Thank you in advance :-)

Henrik
Copenhagen

Hi Henrik,
could be dirt under the trigger of the key.
Had similar problems.
You could try to open the An1x and remove the dirt, it works for me.
It is not very difficult, but there are many screws to remove (30?).

Good luck

Mario


-----Ursprüngliche Nachricht-----
Von: AN1x-list@yahoogroups.com [mailto:AN1x-list@yahoogroups.com]Im
Auftrag von fugmann
Gesendet: Sonntag, 31. Juli 2011 15:14
An: AN1x-list@yahoogroups.com
Betreff: [AN1x] Lowest C is silent on my AN1x


Hi Guys,

I can't get any sound nor MIDI when I hit the lowest C.
Do you have any idea if it is a DIY job to fix?

Thank you in advance :-)

Henrik
Copenhagen



------------------------------------

Community email addresses:
Post message: AN1x-list@yahoogroups.com
Subscribe: AN1x-list-subscribe@yahoogroups.com
Unsubscribe: AN1x-list-unsubscribe@yahoogroups.com
List owner: AN1x-list-owner@yahoogroups.com

Shortcut URL to this page:
http://groups.yahoo.com/group/AN1x-list


Yahoo! Groups Links

fugmann a écrit :

> Hi Guys,
>
> I can't get any sound nor MIDI when I hit the lowest C.
> Do you have any idea if it is a DIY job to fix?
>
> Thank you in advance :-)
>
> Henrik
> Copenhagen
>
>

Hello Henrik!
your issue looks like a bad key contact : neither sound nor MIDI ...
the common point is this contact. You can clean it by yourself, or even
replace it if necessary if you have some basic electronics DIYer
experience. Be careful with the lot of screws in the plastic case and
with the keyboard connectors. During the operation you can check the
small diode (1N 4148 style) wired to the key contact, i don't think it
is the cause of your problem but who knows ? Most diode failures are
short circuits, not open circuit...
Cheers.
J.F.

Thanks Jeff,
 
I worked - I did the job in 30 minutes and now I have a fully functional AN1x - GREAT ;-)
 
Cheers Henrik

Fra: Jeff <jf.serviere@...>

>Til: AN1x-list@yahoogroups.com
>Sendt: 10:43 mandag den 1. august 2011
>Emne: Re: [AN1x] Lowest C is silent on my AN1x
>
>
>  
>
>fugmann a écrit :
>> Hi Guys,
>>
>> I can't get any sound nor MIDI when I hit the lowest C.
>> Do you have any idea if it is a DIY job to fix?
>>
>> Thank you in advance :-)
>>
>> Henrik
>> Copenhagen
>>
>>
>Hello Henrik!
>your issue looks like a bad key contact : neither sound nor MIDI ...
>the common point is this contact. You can clean it by yourself, or even
>replace it if necessary if you have some basic electronics DIYer
>experience. Be careful with the lot of screws in the plastic case and
>with the keyboard connectors. During the operation you can check the
>small diode (1N 4148 style) wired to the key contact, i don't think it
>is the cause of your problem but who knows ? Most diode failures are
>short circuits, not open circuit...
>Cheers.
>J.F.
>
>
>
>

[Non-text portions of this message have been removed]

Hi JF:

If you have a moment, please could you detail how to do this - I have the same problem with the bottom C.

You make it sound fairly straightforward, so would appreciate any tips.

Many thanks in advance,

Andy

a.k.a. "fallingman"

Hi,
It is actually very simple to fix. Remove all the screws (I think there are 32) on the backside. Gently lift away the black back cover.
Please take a look at the attached PDF-document.
1) Gently unplug the 3 connectors, marked with red circles.
2) Remove the little print board
3) Unfasten the larger print board and remove it
4) Now you can see all the connectors from the keys. Use a cotton bud or similar to clean.
5) Gently remove all other dust before assembly
I hope that it works - it takes only half an hour. Please let me know how it went.
Best regards
Henrik :-)
Copenhagen


Fra: Andy Funnell <andy.funnell@...>

>Til: AN1x-list@yahoogroups.com
>Sendt: 16:58 fredag den 16. september 2011
>Emne: Re: [AN1x] Lowest C is silent on my AN1x
>
>
>  
>
>
>
>Hi JF:
>
>If you have a moment, please could you detail how to do this - I have the same problem with the bottom C.
>
>You make it sound fairly straightforward, so would appreciate any tips.
>
>Many thanks in advance,
>
>Andy
>
>a.k.a. "fallingman"
>
>
>
>
>

[Non-text portions of this message have been removed]

Andy Funnell a écrit :

>
> Hi JF:
>
> If you have a moment, please could you detail how to do this - I have the same problem with the bottom C.
>
> You make it sound fairly straightforward, so would appreciate any tips.
>
> Many thanks in advance,
>
> Andy
>
> a.k.a. "fallingman"
>
>
>

Hi Andy !
What's your problem ?
Cheers.
J.F.

Hi !
Sorry for the delay, but i see someone else has answered, thanks Henrik.
I can't say better...
You can use alcohol to clean the contacts with the cotton tip, or a
special contact cleaner sold in electronics DIY shops. Don't use
anything else, no thinner, benzin or trichlorethylene for ex.
Take care of the screws, the case is mostly plastic.
Cheers!
J.F.

Henrik Fugmann a écrit :

> Hi,
> It is actually very simple to fix. Remove all the screws (I think there are 32) on the backside. Gently lift away the black back cover.
> Please take a look at the attached PDF-document.
> 1) Gently unplug the 3 connectors, marked with red circles.
> 2) Remove the little print board
> 3) Unfasten the larger print board and remove it
> 4) Now you can see all the connectors from the keys. Use a cotton bud or similar to clean.
> 5) Gently remove all other dust before assembly
> I hope that it works - it takes only half an hour. Please let me know how it went.
> Best regards
> Henrik :-)
> Copenhagen
>
>
> Fra: Andy Funnell<andy.funnell@...>
>> Til: AN1x-list@yahoogroups.com
>> Sendt: 16:58 fredag den 16. september 2011
>> Emne: Re: [AN1x] Lowest C is silent on my AN1x
>>
>>
>>
>>
>>
>>
>> Hi JF:
>>
>> If you have a moment, please could you detail how to do this - I have the same problem with the bottom C.
>>
>> You make it sound fairly straightforward, so would appreciate any tips.
>>
>> Many thanks in advance,
>>
>> Andy
>>
>> a.k.a. "fallingman"
>>
>>
>>
>>
>>
> [Non-text portions of this message have been removed]
>
>

Hi everybody, I have the same problem, the lower C!!! Need to clean the black rubber? look the picture please http://s11.postimg.org/sn6fnhzmb/20151030_214639.jpg

 

try to slide it and clean but didn' work :(