Ello..
Recently got a4000 and got also some questions about it,tried to get the
info on a5000/a4000 mailing list with nearly no responce... so i'm trying
her, hope you guys wont flame me 8]:
I have got problems with my controller... I use for it my an1x and, i don't
know why, values from controller are accumulated with
the values set up in for eg filter set up (settings like -0 , +127 happen
(but it's not shown of
course). How 2 configure controller or a sampler to have a sampler set the
same value as on the an1x display (0-127) ?
for egzample if filter cutoff is set at 33 then the outside controller can
control parameter in 63 range so the maximum value is 33 + 63 = 96 and the
minimum is 33-63 = - 30... how to make a set up in a way , that no matter
what value is set as a bisic value ( in this case cutoff at 33) i could
allways get 'normal' values from controller ( and that is 0-127), no more,
no less...
i'm not paranoid, it really happens this way; it's heard at best at band
pass and high pass filters get values higher than 127 and lower than 0...
there's no problem with controlling, when basic value in sampler is 64 ...
but i don't want my sampler values be always at 64... it sucks..
just want to controll parameters in 'direct' way ( like it is on an1x)..
thx for answers & respect
----- Original Message -----
From: <jondl@...>
To: <AN1x-list@egroups.com>
Sent: Thursday, December 14, 2000 3:54 AM
Subject: [AN1x-list] Re: AN1x assign question
> Hello Jim,
>
> --- In AN1x-list@egroups.com, "James Ellemore" <J_ellemore@h...>
> wrote:
> > I need some assistance with the following.
> >
> > How can I set my an1x assign knobs to controll filter cutoff & res
> for my E-mu e5000 ultra sampler? Is anyone else using this combo? The
> sequencer I am using is logic audio 4.Can I also set the assign knobs
> to control the fx on the e5000.
>
> On the AN1x, from the UTILITY/SETUP menu, use the rocker button
> beneath 'Ctrl Device' to select which Real Time Controller you wish to
> use, i.e., MW, or RBNX, or Knob 1, etc. Then, use the rocker button
> beneath 'Ctrl No.' to assign a MIDI Change Control message between 1 -
> 95. MIDI CC #074 is Typically used for Filter Cutoff (sometimes called
> Brightness) and MIDI CC #071 for Resonance (or Harmonic Content.)
> Once these assignments are made they will transmitted on the base 'MIDI
> Tx Ch' - and will be rechanneled accordingly to the currently selected
> track within Logic. At least, that's how it suppose to work ;-)
>
> In my set-up I use the AN1x as a master keyboard for my ASR-X Pro
> sampler. Typically, I have Assign Knob 5 set to MIDI CC #074 for
> Filter Cutoff and Assign Knob 6 set to MIDI CC #077 for Resonance. I
> know that I just said MIDI CC #071 is typically used for Resonance but
> my ASR-X requires #077 for resonance NOT #071. The point being - check
> the MIDI Implementation chart in the reference manual for your E5000 to
> confirm MIDI CC # mappings. Ensoniq deviated from the std MIDI CC #
> mappings in the ASR-X - that's all :-)
>
> Regarding the FX control in your E5K - I don't know what real time
> mappings are available to the internal E5K FX. It's been awhile since
> I glanced at the E5K PDF on the E-mu web site but I _think_ you can
> control no more than one parameter at a time on the E5K FX from a
> MIDI CC # of your choice (don't quote me on that.) Again, in my set-up,
> I use Assign Knob 4 set to MIDI CC #012 to control the FX on my ASR-X
> sampler. It works well for me. BTW - have you checked out their new
> RFX card? Pretty cool (and for a "modest" $795 ha ha ha LOL)
>
> >
> > Any assistance would be great.
>
> HTH
>
> >
> > jim
>
> regards,
> Jon
>
>
>
>
>
> Community email addresses:
> Post message: AN1x-list@onelist.com
> Subscribe: AN1x-list-subscribe@onelist.com
> Unsubscribe: AN1x-list-unsubscribe@onelist.com
> List owner: AN1x-list-owner@onelist.com
>
> Shortcut URL to this page:
> http://www.onelist.com/community/AN1x-list
>
> ---
> http://www.strefacd.pl - kliknij i wygraj! Codziennie nagrody! Na stronie:
> Encyklopedia PC - nieznane fakty oraz tajniki dzialania i rozbudowy.
>
>
---
Posiadasz konto komercyjne w K.K.I. ? jesli nie koniecznie sprawdz:
>>> http://www.kki.pl/kki/oferta/cen_uslug.htm <<<
nasze konta sa chronione przez SYSTEM ANTYWIRUSOWY