Thanks for the info.
I'm guessing the one you bought from Maplin, doesn't really perform as
specified.
On 14/10/10 18:54, arthtrin wrote:
>
> Its been a couple of years since I started this post. I think I know what the culprit of this problem with the sounds on my AN1x were. The culprit was the power supply. Just a few days ago I resurrected my AN1x from the attic but lost the power supply. I then found a power supply which was 12v 600mA from a hard drive I have and it worked like a charm on my AN1x with no problems with sounds going weird or fading etc. The only problem was that I had to change the internal battery. However I was a bit worried using the power supply as it is 600mA instead of the required 700mA so I went to my local Maplin store and bought a power supply with volts selector. I then adjusted the volts selector to 12V (which according to the box has 1.4amp) and connected it to my AN1x. After a while of it being connected I started having the problems with the sounds going all weird again. I then disconnected the power supply and reconnected my other power supply and it was back working normal agai
n.
>
> I am convinced that the power supply I used originally on my AN1x and the new one I bought from Maplin was and is the problem.
>
> Art
>
>
>
> --- In AN1x-list@yahoogroups.com, Jeff<jf.serviere@...> wrote:
>>
>> It looks more likely like a ribbon controller problem : play, hit it
>> gently with your fingertip and listen...maybe you'll have to open your
>> synth , clean and plug firmly the ribbon controller connector to fix it.
>> The connectors and IC sockets are often the hidden "Achille's heel" of
>> electronic devices.
>> For the supply unit : these wallwarts are often crap pieces of
>> electronics, but mine works perfectly (at the moment, maybe
>> tomorrow.??). The Yamaha unit is a bit expensive for what it is, but you
>> can try any similar supply rated at 12V - 700 mA, "+" at the center of
>> the connector. Don't try higher voltages, but a 1 amp supply will work
>> even better.
>> Cheers.
>> J.F.
>>
>> jammie a écrit :
>>>
>>>
>>> is your psu large enough as its getting hotter it sounds like the
>>> voltage is dropping i had this problem with a faulty psu it would
>>> start after 5 minutes and the sounds would start to get distorted
>>>
>>> psu are the biggest problem with any electronic equipment and
>>> wallwarts are the worst as everything is compacted into a plug size
>>> package
>>>
>>> get another psu and try that first before suspecting the synth
>>> ----- Original Message -----
>>> From: jondl_2000
>>> To: AN1x-list@yahoogroups.com<mailto:AN1x-list%40yahoogroups.com>
>>> Sent: Sunday, September 20, 2009 6:10 AM
>>> Subject: [AN1x] Re: Sound problems with AN1x
>>>
>>> --- In AN1x-list@yahoogroups.com<mailto:AN1x-list%40yahoogroups.com>,
>>> "palemilk"<palemilk@> wrote:
>>>>
>>>> --- In AN1x-list@yahoogroups.com
>>> <mailto:AN1x-list%40yahoogroups.com>, "Arthur Alexander Crichton"
>>> <ac010b4919@> wrote:
>>>>>
>>>>> Hi,
>>>>>
>>>>> I have a problem with my Yamaha AN1x.
>>>>>
>>>>> When I select some pad sounds on my AN1x the sounds are bright and
>>>>> after about 3 seconds the sound just cuts off to a duller sound which
>>>>> is very low in volume. When I press the keys again all I get is a
>>>>> faint dull sound. I try to play the keys harder but I still get this
>>>>> sound. Before I had this problem, those paticular patches used to
>>>>> sound bright and full. Also, I have noticed some sounds sound thinner
>>>>> than what they used to and that sounds that rely on arpeggio or lfo
>>>>> sound muddy and strange.
>>>>>
>>>>> What is wrong with my beloved AN1X?
>>>>>
>>>>> I have tried cleaning the control knobs with switch cleaner but I
>>>>> still get the same problem. BTW the rom version on my AN1x is v1.02
>>>>>
>>>>> Please help.
>>>>>
>>>>>
>>>>> Arthur
>>>>>
>>>>
>>>> I realize this thread/topic is over a year old, but I recently got
>>> an AN1x again (had one a few years ago) and was experiencing this
>>> exact problem as stated in the original topic. Some patches sound
>>> normal for awhile and then suddenly sound thinner. After messing
>>> around with it for a bit trying to isolate the cause I'm 99% convinced
>>> this is a ribbon controller issue (specifically the Z axis). Applying
>>> pressure or tapping the ribbon cures the problem, but it can reoccur
>>> again after powering down and powering on.
>>>>
>>>> I plan on opening up the synth to check for a loose ribbon connector
>>> and to clean some contacts. Just wanted to add a reply in case anyone
>>> else searches this topic (like I just did) and is looking for possible
>>> answers.
>>>>
>>>> BTW, the AN1x I just picked up is a mint condition unit. First owner
>>> used it once or twice and then kept it in a closet for the past 10
>>> years. Everything was in perfect like new condition...synth, power
>>> supply, manuals, box. Software OS version is v1.03.
>>>>
>>>> Cheers,
>>>> -Todd
>>>>
>>>
>>> Gosh, we had threads on this awhile ago... the Ribbon Controller
>>> always seemed a bit unpredictable.
>>>
>>> I think the most common issue was was being able to tap the ribbon
>>> would cause it to 'hold' at that value rather than jump back to the
>>> default value and for others it would not work as advertised. It was
>>> an intermittent thing, and while some of us could reproduce the issue
>>> it was never under the same circumstances as another user, i.e. using
>>> different voices. And it seem to clear after a power on/off cycle.
>>>
>>> Sound likes you've rediscovered this issue.
>>>
>>> Jon
>>>
>>> ----------------------------------------------------------
>>>
>>> No virus found in this incoming message.
>>> Checked by AVG - www.avg.com
>>> Version: 8.5.409 / Virus Database: 270.13.107/2382 - Release Date:
>>> 09/19/09 06:03:00
>>>
>>> [Non-text portions of this message have been removed]
>>>
>>>
>>
>
>
>
>
> ------------------------------------
>
> Community email addresses:
> Post message: AN1x-list@yahoogroups.com
> Subscribe: AN1x-list-subscribe@yahoogroups.com
> Unsubscribe: AN1x-list-unsubscribe@yahoogroups.com
> List owner: AN1x-list-owner@yahoogroups.com
>
> Shortcut URL to this page:
> http://groups.yahoo.com/group/AN1x-list
>
> The AN1x Control Synthesizer FAQ::
> http://www.geocities.com/jondl_2000/an1x_faq/an1x_faq_toc.htm
> Yahoo! Groups Links
>
>
>
>