I have tested my AN1x with just the headphones connected and the
problem seems to have disappeared. I then tested with the line
outputs connected and still there is no problem. Finally I tested
with the headphones and line outputs both connected and again no
problems.
The problem seems to have disappeared.
Could it be that...
1) I pressed the "assign" button while powering on the synth that
fixed the problem
or
2) My AN1x is temperamental?
Cheers
Arthur
--- In
AN1x-list@yahoogroups.com, "Arthur Alexander Crichton"
<ac010b4919@...> wrote:
>
> Haha its been along time since someone has called me Alex:) Ok, I
> have removed the left and right line outputs and left the
headphones
> in. So far the problem has disappeared. I will disconnect the
> headphones and connect the line outputs and see if the problem
> returns.
>
> I'll report back if there is any probems.
>
> Cheers
>
> Arthur
>
>
> --- In AN1x-list@yahoogroups.com, Jeff <jf.serviere@> wrote:
> >
> >
> > Hello Alex!
> > as you describe your problem it looks like something wrong in the
> analog output circuit: dry solder joint, bad contact or some "ill"
op
> amp or transistor that goes out when hot. The heat related failure
is
> probable because it works well for a short time and after the sound
> decreases, a contact problem would occur more irregularly. I'm not
at
> home currently, so i cannot open mine to tell you what to look and
> where. I don't think it is a fatal issue at all, but it could take
a
> long time to find the faulty part.
> > You can try 2 things without opening the synth:
> > First remove all additional devices (effects, patch bay..)
between
> the AN1x and the amp or mixer.
> > Then turn on your synth with the line out plugged only,play it,
> > and after do the same thing without line out but with headphones
> only.
> > If you're using a mixer try another input with the line out
> connected.
> > Look (or more likely hear !) if there is some difference....
> > Cheers
> > J.F.
> >
> >
> > > Message du 14/02/08 00:42
> > > De : "Arthur Alexander Crichton"
> > > A : AN1x-list@yahoogroups.com
> > > Copie à :
> > > Objet : Re: [AN1x] Sound problems with AN1x
> > >
> > > > Ok, I tried a factory reset and played the affected sounds
> again and
> > > it seemed to fix the problem. Then I leave my AN1x on and 5
> minutes
> > > later the problem comes back:(
> > >
> > > What will I do? Is my AN1x ready for the synth graveyard in the
> sky?
> > >
> > > Please advise
> > >
> > > Arthur
> > >
> > > --- In AN1x-list@yahoogroups.com, "Arthur Alexander Crichton"
> > > ...> wrote:
> > > >
> > > > How do I reload the OS?
> > > >
> > > > Is it the same as a factory reset? If so, I did a factory
reset
> but
> > > > the problem still persists.
> > > >
> > > > The problem is when I keep the key pressed the sound just
> abruptly
> > > > goes dull and low in volume which it shouldn't do. Its like
the
> > > > cutoff has gone to "0" and the main volume has gone low.
> > > >
> > > > Cheers
> > > >
> > > > Arthur
> > > > --- In AN1x-list@yahoogroups.com, nung242 wrote:
> > > > >
> > > > > I would try backing up your patches, then maybe reload the
> OS. It
> > > > worked for a problem I was having on my K-Station. Good Luck!
> > > > >
> > > > > http://www.youtube.com/tillthenmusik See the AN1x in
> > > > action on the song " legend "
> > > > >
> > > > > Arthur Alexander Crichton >
> > > > wrote: Hi,
> > > > >
> > > > > I have a problem with my Yamaha AN1x.
> > > > >
> > > > > When I select some pad sounds on my AN1x the sounds are
> bright
> > > and
> > > > > after about 3 seconds the sound just cuts off to a duller
> sound
> > > > which
> > > > > is very low in volume. When I press the keys again all I
get
> is
> > > a
> > > > > faint dull sound. I try to play the keys harder but I still
> get
> > > > this
> > > > > sound. Before I had this problem, those paticular patches
> used
> > > to
> > > > > sound bright and full. Also, I have noticed some sounds
sound
> > > > thinner
> > > > > than what they used to and that sounds that rely on
arpeggio
> or
> > > > lfo
> > > > > sound muddy and strange.
> > > > >
> > > > > What is wrong with my beloved AN1X?
> > > > >
> > > > > I have tried cleaning the control knobs with switch cleaner
> but
> > > I
> > > > > still get the same problem. BTW the rom version on my AN1x
is
> > > v1.02
> > > > >
> > > > > Please help.
> > > > >
> > > > > Arthur
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > > ---------------------------------
> > > > > Never miss a thing. Make Yahoo your homepage.
> > > > >
> > > > > [Non-text portions of this message have been removed]
> > > > >
> > > >
> > >
> > >
> >
> >
> > [Non-text portions of this message have been removed]
> >
>