Hello!
do you have the (awful) user manual?
I'll take a look at my own synth for your OS problem (mine is maybe
different...) and to see how i managed to morph between 2 scenes.
Because i did it: for organ sounds it works well because both sounds
have the same pitch ; i've tried to morph 2 different typical synth
sounds (VCOs sync'ed, filter sweep and so on) and, one being 1 octave
lower just as you've tried to do, i got the same results than you, the
pitch changes when you move the mod wheel.
Be patient: these days i'm more in the kitchen and parties (i'm french,
nobody's perfect) than behind my keyboards, and my motorcycle needs some
brake pads change!
Happy new year to you all!
J.F.
gwynforevans a écrit :
>Hi Jeff: thanks for your comprehensive reply.
>
>I worked around this, as mentioned in both mine and your other emails
>yesterday, but I wanted to comment that I do not have the option in
>Utility Setup Device or Ctrl No to select "Scene Ctrl". Only
>"SceneSel" is available in both menus in the relevant place, it being
>number 3 in the list of 90-something controls. Number 4 is blank, as
>are several others in the list.
>
>It may be my OS version or something (it displaying "TEST MODE V 1.02"
>when I start up and hold down 0 + and - together.
>
>Secondly, the copying of the scene did not work even when I followed
>to method you suggest below! I ∗can∗ swap, and I ∗can∗ copy from
>other voices, I just cannot copy scene 1 to scene 2.
>
>Many thanks for your help,
>Gwyn
>
>--- In AN1x-list@yahoogroups.com, Jeff <jf.serviere@...> wrote:
>
>
>>Hello Gwyn!
>>To copy data from another voice to a scene:
>>
>> ∗ hold the "scene1" or "scene2" switch and enter the number of the
>> voice whose data you want to copy. The screen will display this
>> number flashing together with "sceneX load?"
>> ∗ Press "yes" (or "no" if it's a mistake!), that's all.
>>
>>To swap both scenes (ie sound data are exchanged between "scene1" and
>>"scene2") :
>>
>> ∗ hold the "store" switch and press both "scene1" and "scene2"
>> switches. The screen will display "Scene 1<->2 Swap" with "sure?"
>> flashing
>> ∗ As previously press "yes" or "no".
>>
>>To "morph" between both scenes the continuous controller (modulation
>>wheel = MW) must be assigned to "scene control" ( Scene Ctrl on the
>>screen) and not "scene select" (Scene Sel) . In the last case the mod
>>wheel only toggles between the 2 scenes like the switches as you
>>mentionned, in the first it is defined as a continuous controller
>>allowing to mix both sounds depending on its position. To check which
>>controller is assigned (if any..) to the Scene Control (i.e. "morphing"
>>or "mix") hold both scene switches, it will be displayed on the screen.
>>N.B1.: this "morphing" function can be assigned to any continuous
>>controller, not only the mod wheel, for example a foot controller, with
>>a pot inside like an expression pedal, not a simple switch as the
>>sustain pedal. However this simple pedal switch can be assigned to
>>something else than the sustain, assuming this parameter does require
>>only a 1 or 0 value.
>>N.B.2: The "sustain" pedal can be any fitted with a "normally closed"
>>type momentary switch and a mono jack : you can find it easily
>>
>>
>(music or
>
>
>>electronics stores) and cheaper than the Yamaha "FC something" model....
>>NB3: Caution! The continuous foot controllers are a little bit more
>>complex, if they will fit or not depends on the pot ohmic value and the
>>jack wiring !
>>Xmas greetings
>>J.F.
>>
>>
>>
>>
>>Gwyn Evans a écrit :
>>
>>
>>
>>>Hi there. I am new! I have had an AN1 for some years and I am
>>>
>>>
>finally having the time to use it properly.
>
>
>>>I have created my own noise, a bass noise using both VCOs and based
>>>
>>>
>on the default Type 2 noise the system offers you when you start creating.
>
>
>>>I wanted quickly to copy scene 1 to scene 2 so that scene 3 could
>>>
>>>
>differ in pitch by an octave. This does not appear to be possible, in
>that I tried it, but it didn't do anything (i.e. I went into scene 2,
>and attempted the copy but it simply refused to do it, despite
>appearing as though it was doing it.
>
>
>>>So I manually copied it.
>>>
>>>My question is this: I want to morph between the two bass sounds,
>>>
>>>
>and when I set either the modulation wheel or one of the assignable
>Knobs to SceneSel, it just alternates between the scenes, without
>morphing between them.
>
>
>>>I think that there is a setting wrong somewhere that is stopping it
>>>
>>>
>from behaving in the way that I expect: does anyone know what that
>setting is?
>
>
>>>I have changed the layer mode from single, to dual, to unison etc
>>>
>>>
>etc, and depressed both scene buttons, but it is still not doing it.
>
>
>>>Any advice would be gratefully received.
>>>
>>>Many thanks
>>>
>>>Gwyn
>>>
>>>
>>>
>>>
>>> ___________________________________________________________
>>>Yahoo! Answers - Got a question? Someone out there knows the
>>>
>>>
>answer. Try it
>
>
>>>now.
>>>http://uk.answers.yahoo.com/
>>>
>>>
>>>
>>>
>>>
>
>
>
>
>