[sdiy] s612-ax73 cable

[John L Marshall]

Cables are available several ways; a group of conductors, singles or pairs
and a single shield for the whole bunch (most common), single conductors
with a shield for each (hardest to find), and pairs of conductors with
shield for each pair (fairly common). Murphy works overtime. You need six
conductors with six shields. All shields are tied common at each connector.

I looked in Radio Shack Commercial Catalog and Mouser and did not see what
you need. You could use a cable with 6 shielded pairs. Many of the cables
have individual conductors at 22 AWG. I would prefer a lighter cable with 24
or 26 AWG conductors.

John
----- Original Message -----
From: gregory zifcak <zifcak at hotmail.com>
To: <john.l.marshall at gte.net>; <synth-diy at dropmix.xs4all.nl>
Sent: Tuesday, October 23, 2001 4:43 PM
Subject: Re: [sdiy] s612-ax73 cable


> i was assuming that in a shielded 6 conductor cable that each would be
> shielded. is this not the case?
>
> greg
>
>
> >From: "John L Marshall" <john.l.marshall at gte.net>
> >To: "gregory zifcak" <zifcak at hotmail.com>, <jlarryh at iquest.net>,
> ><synth-diy at dropmix.xs4all.nl>
> >Subject: Re: [sdiy] s612-ax73 cable
> >Date: Tue, 23 Oct 2001 16:06:00 -0700
> >
> >It is probably best that each conductor be individually shielded. With
one
> >common shield you are inviting crosstalk between the voices. Can you can
> >live with crosstalk between the voices?
> >
> >John
> >
> >----- Original Message -----
> >From: gregory zifcak <zifcak at hotmail.com>
> >To: <jlarryh at iquest.net>; <synth-diy at dropmix.xs4all.nl>
> >Sent: Tuesday, October 23, 2001 2:38 PM
> >Subject: Re: [sdiy] s612-ax73 cable
> >
> >
> > > thanks larry and atom,
> > >
> > > >Pin 1 = voice 3
> > > >Pin 2 = voice 2
> > > >Pin 3 = voice 1
> > > >Pin 4 = common ground / shield
> > > >Pin 5 = not connected
> > > >Pin 6 = voice 6
> > > >Pin 7 = voice 5
> > > >Pin 8 = voice 4
> > > >Pin 9 through pin 13 not used
> > >
> > > so i should just get shielded six conductor cable, two male
connectors,
> >and
> > > connect the corresponding voice pins together, ignoring 4 and 9-13,
> >right?
> > > or do i need 7 conductor to hook up pin 4 as well?
> > >
> > > greg
> > >
> > >
> > >
> > > >The outer metal part of the connector is also connected to ground.
> >That
> > > >should help you locate pin 4 as they are shorted together.
> > > >
> > > >The cable does need to be shielded as it is low level audio.  All
> >signals
> > > >are unbalanced.
> > > >Larry Hendry
> > > >
> > > >
> > >
> > >
> > > _________________________________________________________________
> > > Get your FREE download of MSN Explorer at
> >http://explorer.msn.com/intl.asp
> > >
> >
>
>
> _________________________________________________________________
> Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp
>