Hi,
now i´ve decided to hard-wire the knobs directly to the Oscillator-
Effects-Unit, cause the program-unit isn´t very important for me. It
works fine, but i must leave the KLM-367 in the case cause of TE, ST
and IR, first because i don´t know their function, 2nd doesn´t the
OSC-Board work without those Pins (i believe that IR is the
Interrupt, but the Interrupt for what?).
Anyway, the hard-wiring works. Ok, Cutoff works now from 100 to 0%
etc and Mg doesn´t also work anymore. It seems that MG has
permanently 100% speed cause the Poly sounds kinda 70´s Top-octave-
Generator Organ. Does the KLM-367 organize the MG function and route
it to the necessary pins (VCO/VCF) or is there a Single pin on CN05
which is an input for MG-Level?
Greetings
stef
--- In
PolySix@yahoogroups.com, Johannes Hausensteiner
<jo.synth@c...> wrote:
>
> 1)
> +----------+-------+
> |Inh C B A | Com |
> +----------+-------+
> | 0 0 0 0 | Inp 0 |
> | 0 0 0 1 | Inp 1 |
> | 0 0 1 0 | Inp 2 |
> | 0 0 1 1 | Inp 3 |
> | 0 1 0 0 | Inp 4 |
> | 0 1 0 1 | Inp 5 |
> | 0 1 1 0 | Inp 6 |
> | 0 1 1 1 | Inp 7 |
> | 1 x x x | Hi Z |
> +----------+-------+
>
> 2) see attachment
>
> 3)
> +-------------------+----------+---+
> |CN03- 1 EFF.SP/INT | -5V..+5V | a |
> | 2 CHO | 0V/+5V | d |
> | 3 PHA | 0V/+5V | d |
> | 4 ENS | 0V/+5V | d |
> | 5 VCA MOD | 1Vp-p | a |
> | 6 P.VOL | 0V..+5V | a |
> | 7 RESO | 0V..+10V| a |
> +-------------------+----------+---+
> |CN05- 1 EG MODE | 0V/+5V | d |
> | 2 SUB OFF | 0V/+5V | d |
> | 3 SUB 1/2 | 0V/+5V | d |
> | 4 /| | 0V/+5V | d |
> | 5 RELEASE | -5V..+5V | a |
> | 6 SUSTAIN | -5V..+5V | a |
> | 7 DECAY | -5V..+5V | a |
> | 8 ATTACK | -5V..+5V | a |
> | 9 RESO | 0V..+10V| a |
> | 10 EG INT | -5V..+5V | a |
> | 11 PW/PWM | 0.2..2.4V| a |
> | 12 VCO MOD | | a |
> | 13 VCF MOD/CF |-7.5..7.5V| a |
> | 14 KBD TRACK | -5V..+5V | a |
> | 15 TE | 0V/+5V | d |
> | 16 ST | 0V/+5V | d |
> | 17 4' | 0V/+5V | d |
> | 18 8' | 0V/+5V | d |
> | 19 IR | 0V/+5V | d |
> +-------------------+----------+---+
>
>
> Stefan Rinass wrote:
> > Hi all,
> >
> > i have a few questions. Does anyone know how the ABC-Lines for
the
> > 4051´s located on KLM-370 are coded (Inhibit 0/1, Line A/B/C =
Knob ?)
> >
> > 2nd question is Connector CN10, how is it driven? Is it a pure
> > Key-Matrix-Driver?
> >
> > 3rd quesion is CN05 and CN03, are the driving Voltages pure +5
and -5 Volts?
> >
> > Thanks
> >
> > Stef
> >
> >
> >
> > PolySix "Digiest" Page: http://www.acc.umu.se/~amber/Poly6
> > Yahoo! Groups Links
> >
> >
> >
> >
> >
> >
> >
>
>
> [Non-text portions of this message have been removed]