Hi,
Most probably IC1 on KLM-370 (the 4051 analog mux) is dead. I had this
before; the leaked battery acid crawls along the thick black ground wire
up to KLM-370 and continues its destructive work there. Replace that
black wire as well.
Good luck!
Johannes
On 29.05.2014 13:34, Bob Grieb bobgrieb@yahoo.com [PolySix] wrote:
>
>
>
> Hi,
>
> So it seems that all of those connections are OK. Please check the
> IC23 connections next. P23 from IC22 to IC23-12,13,8, and the other
> connections on IC23 which you can see on the schematic. I am assuming
> that you do not have an oscilloscope, right?
>
> You say you have 13.56 volts at IC10-1 That's interesting, as
> IC18 outputs should range from -5 to +5 only. Does IC10 have -15
> on pin 4? Does IC18 have +5 on pin 16 and -5 on pin 7?
>
> Bob
>
> ------------------------------------------------------------------------
> ∗From:∗ "Phil65 phil0065@yahoo.fr [PolySix]" <PolySix@yahoogroups.com>
> ∗To:∗ PolySix@yahoogroups.com
> ∗Sent:∗ Thursday, May 29, 2014 4:47 AM
> ∗Subject:∗ Re: [PolySix] EG and VCF not working after battery leakage
>
> Looking at the klm367 schematic, I understand now your point with the
> connections between pins and signal P20, P21 and P22 but I had some
> diffuculty to cross link that information with the PCB drawing... until
> I realize that i was counting incorrectly the pins while I did know that
> it was from top right then CCW
> Do what I say, not what I do... I was correct for top side numbers but
> reverse for the bottom side i.e i did restart with 9 below 1... Stupid!
>
> So now I do have the following:
>
> P22 IC18-9 IC19-9 and IC22-23 => OK
> P21 IC18-10 IC19-10 and IC22-22 => OK
> P20 IC18-11 IC19-11 and IC22-21 => OK
> INH IC19-6 and IC23-10 => OK
> "X" IC18-3 and IC19-3 and IC27-1 =>OK
>
> I did recheck my previous post to correct them in light of my wrong pin
> counting
>
> 1) I did the DAC calib again and turning VR6 CCW => from led 8 to led 7
> 6 then 5, while turning VR7 CCW from led 8 to 7 then 6
> OK
>
> 2) pin 3 of IC18 and pin 1 of IC27, OK
> OK
>
> 3) pin 6 of IC18 and IC23-4. OK
> OK
>
> 4) pins 9,10 and 11 of IC18 and 19 should be connected to each other and
> to IC22 ?
>
> UPDATED: Wrong comment see above!
>
> 5) With power on, you should be able to vary a front panel
> control,such as filter cutoff, and see IC7 pin 7 change voltage as you
> do it (in manual mode).
>
> 3.177V => 3.120V cut off from 10 to 0 with all controls at normal setting
>
> UPDATED: Luckily correct, I did measure in fact pin 6 but it is strapped
> to pin 7...
>
> 6) when you select different patches, you should see the attack at
> IC10-1decay
>
> => On IC 10-1 no change always 13.56V
>
> UPDATED: Correct measurement
>
> 7) Decay at IC10-7 ?
>
> =>slight variation between patches. In manual mode and normal setting
> with decay control from 0 to 10 => 3.240V to 3.346V
>
> UPDATED: Again Luckily correct, I did measure in fact pin 6 but it is
> strapped to pin 7...
>
> I apologize for my mistake and thanks again for your patience and your
> support.
> Phil
>
> --------------------------------------------
> En date de : Jeu 29.5.14, Bob Grieb bobgrieb@yahoo.com [PolySix]
> <PolySix@yahoogroups.com> a écrit :
>
> Objet: Re: [PolySix] EG and VCF not working after battery leakage
> À: "PolySix@yahoogroups.com" <PolySix@yahoogroups.com>
> Date: Jeudi 29 mai 2014, 3h28
>
>
> These should be
> connected:
> IC18-9 IC19-9 and IC22-23 this
> is signal "P22"
> IC18-10 IC19-10 and IC22-22
> this is signal
> "P21"
> IC18-11 IC19-11 and IC22-21
> this is signal "P20"
> IC19-6 and
> IC23-10
> Also, IC18-3 must connect to
> IC19-3 as well as to IC27-1 which you checked already.
>
> You may want to download the
> service manual as it is available forfree on the web, and see the
> schematic for KLM-367.
> If IC18 and IC19 are not
> connected properly, the control voltages
> won't work
> correctly.
> Please ignore IC22 pins 5, 19,and
> 35. They are not related to
> this discussion. We are
> checking A B C and INH signals to IC18 and
> IC19.
> Bob
>
>
>
> From: "Phil65
> phil0065@yahoo.fr [PolySix]"
> <PolySix@yahoogroups.com>
> To:
> PolySix@yahoogroups.com
> Sent: Wednesday, May
> 28, 2014 7:55 PM
>
> Subject: Re: [PolySix]
> EG and VCF not working after battery leakage
>
>
>
>
>
>
>
>
>
>
>
>
> Hi Bob,
>
> You are really helpfull. Merci !
>
>
>
> 1) I did the DAC calib again and turning VR6 CCW => from
> led 8 to led 7 6 then 5, while turning VR7 CCW from led 8
> to 7 then 6
>
> 2) pin 3 of IC18 and pin 1 of IC27, OK
>
> 3) pin 6 of IC18 and IC23-4. OK
>
> 4) pins 9,10 and 11 of IC18 and 19 should be connected to
> each other and to IC22 ?
>
> It seems I have a problem here. I found only IC18-9 +
> IC19-9 + IC22 -5 , IC22-19 and IC22-35 connected together.
> Nothing between IC18-10 (IC18-11) with any pin of IC19 or
> IC22 ??
>
> Shall I strap IC18-9 + 10 + 11
>
>
>
> 5) With power on, you should be able to vary a front
> panel
>
> control,such as filter cutoff, and see IC7 pin 7 change
> voltage as you
>
> do it (in manual mode).
>
>
>
> 3.177V => 3.120V cut off from 10 to 0 with all controls
> at normal setting
>
>
>
>
>
> 6) when you select different patches, you should see the
> attack at IC10-1decay
>
>
>
> => On IC 10-1 no change always 13.56V
>
>
>
> 7) Decay at IC10-7 ?
>
>
>
> =>slight variation between patches. In manual mode and
> normal setting with decay control from 0 to 10 => 3.240V
> to 3.346V
>
>
>
> Thanks for your help, really appreciated !
>
> Phil
>
>
>
> --------------------------------------------
>
> En date de : Jeu 29.5.14, Bob Grieb bobgrieb@yahoo.com
> [PolySix] <PolySix@yahoogroups.com> a écrit :
>
>
>
> Objet: Re: [PolySix] EG and VCF not working after battery
> leakage
>
> À: "PolySix@yahoogroups.com"
> <PolySix@yahoogroups.com>
>
> Date: Jeudi 29 mai 2014, 0h21
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
> Hi Phil,
>
>
>
> If you are seeing LEDs 1 and 8 in DAC calibration mode,
> that
>
> impliesthat
>
> the DAC and the input muxes are working. Another
> thing
>
> to try -
>
> in
>
> the DAC calibration test mode, turn the two controls
> that
>
> you were supposedto
>
> set for this test, and you should see the LED's
>
> change.
>
>
>
> Don't worry about the click noise test for
>
> now.
>
>
>
> The voltage demux for controlling the EG and the VCF is
>
> mostlyIC18
>
> (4051). I would check with the ohmmeter that you
> have
>
> good connections(with
>
> the power off, of course) between pin 3 of IC18 and pin 1
> of
>
> IC27, and between
>
> pin
>
> 6 of IC18 and IC23-4. Also, pins 9,10 and 11 of IC18
> and
>
> 19 should be connectedto
>
> each other and to IC22.
>
>
>
>
>
> With power on, you should be able to vary a front panel
>
> control,such
>
> as filter cutoff, and see IC7 pin 7 change voltage as
> you
>
> do it (in manual
>
> mode).
>
> And when you select different patches, you should see
> the
>
> attack at IC10-1decay
>
> at IC10-7, etc changing with different patches. Be
> careful
>
> when probing with
>
> the
>
> power on not to short anything or you can damage chips in
> an
>
> instant. Use the gndtest
>
> pt for the meter black or negative lead.
>
>
>
>
>
>
>
> Tell us what you measure at these points in the circuit
> and
>
> if they vary with the
>
> corresponding
>
> front panel control in manual mode, or when you change
>
> patches.
>
>
>
> Bob
>
>
>
>
>
> From:
>
> "Phil65 phil0065@yahoo.fr [PolySix]"
>
> <PolySix@yahoogroups.com>
>
> To:
>
> PolySix@yahoogroups.com
>
> Sent: Wednesday, May
>
> 28, 2014 6:05 PM
>
> Subject: Re: [PolySix]
>
> EG and VCF not working after battery leakage
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
> Thanks Bob for your quick answer !
>
>
>
>
>
>
>
> Seems that my patch looses "EG" from memory. I
>
> have no sound unless I put the VCA switch from EG back
> to
>
> "square" again to get some sound.
>
>
>
> Not sure to keep the bank memory even when polysix is
> still
>
> on.
>
>
>
>
>
>
>
> I did the procedure and it passes directly. Here a quick
>
> summary:
>
>
>
> ∗dummy 56 ohm => all leds on
>
>
>
> ∗remove resistance => A1 leds
>
>
>
> ∗SW1 in test mode and tape switch to enable => Only
> leds
>
> 1+8 on
>
>
>
> ∗ SW1 back to normal => still leds 1+8
>
>
>
> ∗ "7 ) confirm that output DC click noise is within
> 6V
>
> p-p when power is switched off" => sorry I
> don't
>
> understand precisely what to do/ measure?
>
>
>
> ∗ Power on again => A1 leds on.
>
>
>
>
>
>
>
> Thanks for your support
>
>
>
> Phil
>
>
>
>
>
>
>
> --------------------------------------------
>
>
>
> En date de : Mer 28.5.14, Bob Grieb bobgrieb@yahoo.com
>
> [PolySix] <PolySix@yahoogroups.com> a écrit :
>
>
>
>
>
>
>
> Objet: Re: [PolySix] EG and VCF not working after
> battery
>
> leakage
>
>
>
> À: "PolySix@yahoogroups.com"
>
> <PolySix@yahoogroups.com>
>
>
>
> Date: Mercredi 28 mai 2014, 2h09
>
>
>
>
>
>
>
>
>
>
>
> See if
>
>
>
> these functions can be controlled correctly when using
>
>
>
> patchesin
>
>
>
> memory. If so, then the output from the CPU to the
>
> analog
>
>
>
> circuitsis
>
>
>
> OK. Then you have a problem with reading the
>
>
>
> controls.But
>
>
>
> if the sound is always the same with all programs, then
>
> the
>
>
>
>
>
>
>
> output
>
>
>
> circuit is bad and maybe t is reading from the pots
>
>
>
> OK.Did
>
>
>
> you try the DAC calibration test in the manual? It
>
> would
>
>
>
> be helpfulto
>
>
>
> know if that is working OK. Just the part where you
> try
>
> to
>
>
>
> get the
>
>
>
> two
>
>
>
> LEDs to light up.
>
>
>
>
>
>
>
> Bob
>
>
>
>
>
>
>
>
>
>
>
> From:
>
>
>
> "phil0065@yahoo.fr [PolySix]"
>
>
>
> <PolySix@yahoogroups.com>
>
>
>
> To:
>
>
>
> PolySix@yahoogroups.com
>
>
>
> Sent: Tuesday, May 27,
>
>
>
> 2014 6:02 PM
>
>
>
> Subject: [PolySix] EG
>
>
>
> and VCF not
>
>
>
> working after battery leakage
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
> Bonjour !I am
>
>
>
> French
>
>
>
> and happy to join this group of Polysix owner. My old
>
>
>
> Polysix bought back in
>
>
>
> 1983 has been sleeping in the attic since 1990, until I
>
> have
>
>
>
> returned back now to
>
>
>
> my first love. Unfortunately I have discovered the
>
> battery
>
>
>
> leakage problem !
>
>
>
> So I did
>
>
>
> the standard procedure (like many)Spend a
>
>
>
> lot of time checking the lines on KLM-367 with plenty
> of
>
> leds on at start
>
>
>
> up.. Browse internet for hours (discover service
>
>
>
> manual, old crown, etc)…, change IC
>
>
>
> 30 & 31 … recheck continuity, still few leds
>
>
>
> on..Recheck again, change all set of
>
>
>
> panel switches (vintage planet)..4 leds on... Bank B
> not
>
>
>
> working...Check
>
>
>
> lines again, to get finally only leds A1
>
>
>
> on start up. Great !
>
>
>
> Unfortunately sound
>
>
>
> is not OK.
>
>
>
> Tune seems
>
>
>
> OK,
>
>
>
> 6 voices are OK, voltages from power board are OK (15V,
>
> 5V
>
>
>
> -5V and -15V) all pots
>
>
>
> and switches seem to work except the 4x EG and 4x VCF
>
> pots
>
>
>
> which are not
>
>
>
> active! I think at
>
>
>
> this stage it is useless to do the calibration
> procedure.
>
> Is
>
>
>
> there some indications,
>
>
>
> checking to start with to define if it is still a
>
>
>
> line/continuity problem or if electronic parts (IC,
>
> diode..)
>
>
>
> should be changed.
>
>
>
> Thanks in
>
>
>
> advance for your help
>
>
>
>
>
>
>
>
>
>
>
> Phil
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
> #yiv8680019145 #yiv8680019145 --
>
> #yiv8680019145ygrp-mkp {
>
> border:1px solid #d8d8d8;font-family:Arial;margin:10px
>
> 0;padding:0 10px;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-mkp hr {
>
> border:1px solid #d8d8d8;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-mkp #yiv8680019145hd {
>
> color:#628c2a;font-size:85%;font-weight:700;line-height:122%;margin:10px
>
> 0;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-mkp #yiv8680019145ads
> {
>
> margin-bottom:10px;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-mkp .yiv8680019145ad {
>
> padding:0 0;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-mkp .yiv8680019145ad p
> {
>
> margin:0;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-mkp .yiv8680019145ad a
> {
>
> color:#0000ff;text-decoration:none;}
>
> #yiv8680019145 #yiv8680019145ygrp-sponsor
>
> #yiv8680019145ygrp-lc {
>
> font-family:Arial;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-sponsor
>
> #yiv8680019145ygrp-lc #yiv8680019145hd {
>
> margin:10px
>
> 0px;font-weight:700;font-size:78%;line-height:122%;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-sponsor
>
> #yiv8680019145ygrp-lc .yiv8680019145ad {
>
> margin-bottom:10px;padding:0 0;}
>
>
>
> #yiv8680019145 #yiv8680019145actions {
>
> font-family:Verdana;font-size:11px;padding:10px 0;}
>
>
>
> #yiv8680019145 #yiv8680019145activity {
>
> background-color:#e0ecee;float:left;font-family:Verdana;font-size:10px;padding:10px;}
>
>
>
> #yiv8680019145 #yiv8680019145activity span {
>
> font-weight:700;}
>
>
>
> #yiv8680019145 #yiv8680019145activity span:first-child {
>
> text-transform:uppercase;}
>
>
>
> #yiv8680019145 #yiv8680019145activity span a {
>
> color:#5085b6;text-decoration:none;}
>
>
>
> #yiv8680019145 #yiv8680019145activity span span {
>
> color:#ff7900;}
>
>
>
> #yiv8680019145 #yiv8680019145activity span
>
> .yiv8680019145underline {
>
> text-decoration:underline;}
>
>
>
> #yiv8680019145 .yiv8680019145attach {
>
> clear:both;display:table;font-family:Arial;font-size:12px;padding:10px
>
> 0;width:400px;}
>
>
>
> #yiv8680019145 .yiv8680019145attach div a {
>
> text-decoration:none;}
>
>
>
> #yiv8680019145 .yiv8680019145attach img {
>
> border:none;padding-right:5px;}
>
>
>
> #yiv8680019145 .yiv8680019145attach label {
>
> display:block;margin-bottom:5px;}
>
>
>
> #yiv8680019145 .yiv8680019145attach label a {
>
> text-decoration:none;}
>
>
>
> #yiv8680019145 blockquote {
>
> margin:0 0 0 4px;}
>
>
>
> #yiv8680019145 .yiv8680019145bold {
>
> font-family:Arial;font-size:13px;font-weight:700;}
>
>
>
> #yiv8680019145 .yiv8680019145bold a {
>
> text-decoration:none;}
>
>
>
> #yiv8680019145 dd.yiv8680019145last p a {
>
> font-family:Verdana;font-weight:700;}
>
>
>
> #yiv8680019145 dd.yiv8680019145last p span {
>
> margin-right:10px;font-family:Verdana;font-weight:700;}
>
>
>
> #yiv8680019145 dd.yiv8680019145last p
>
> span.yiv8680019145yshortcuts {
>
> margin-right:0;}
>
>
>
> #yiv8680019145 div.yiv8680019145attach-table div div a {
>
> text-decoration:none;}
>
>
>
> #yiv8680019145 div.yiv8680019145attach-table {
>
> width:400px;}
>
>
>
> #yiv8680019145 div.yiv8680019145file-title a,
> #yiv8680019145
>
> div.yiv8680019145file-title a:active, #yiv8680019145
>
> div.yiv8680019145file-title a:hover, #yiv8680019145
>
> div.yiv8680019145file-title a:visited {
>
> text-decoration:none;}
>
>
>
> #yiv8680019145 div.yiv8680019145photo-title a,
>
> #yiv8680019145 div.yiv8680019145photo-title a:active,
>
> #yiv8680019145 div.yiv8680019145photo-title a:hover,
>
> #yiv8680019145 div.yiv8680019145photo-title a:visited {
>
> text-decoration:none;}
>
>
>
> #yiv8680019145 div#yiv8680019145ygrp-mlmsg
>
> #yiv8680019145ygrp-msg p a span.yiv8680019145yshortcuts
> {
>
> font-family:Verdana;font-size:10px;font-weight:normal;}
>
>
>
> #yiv8680019145 .yiv8680019145green {
>
> color:#628c2a;}
>
>
>
> #yiv8680019145 .yiv8680019145MsoNormal {
>
> margin:0 0 0 0;}
>
>
>
> #yiv8680019145 o {
>
> font-size:0;}
>
>
>
> #yiv8680019145 #yiv8680019145photos div {
>
> float:left;width:72px;}
>
>
>
> #yiv8680019145 #yiv8680019145photos div div {
>
> border:1px solid
>
> #666666;height:62px;overflow:hidden;width:62px;}
>
>
>
> #yiv8680019145 #yiv8680019145photos div label {
>
> color:#666666;font-size:10px;overflow:hidden;text-align:center;white-space:nowrap;width:64px;}
>
>
>
> #yiv8680019145 #yiv8680019145reco-category {
>
> font-size:77%;}
>
>
>
> #yiv8680019145 #yiv8680019145reco-desc {
>
> font-size:77%;}
>
>
>
> #yiv8680019145 .yiv8680019145replbq {
>
> margin:4px;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-actbar div a:first-child
> {
>
> margin-right:2px;padding-right:5px;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-mlmsg {
>
> font-size:13px;font-family:Arial, helvetica, clean,
>
> sans-serif;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-mlmsg table {
>
> font-size:inherit;font:100%;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-mlmsg select,
>
> #yiv8680019145 input, #yiv8680019145 textarea {
>
> font:99% Arial, Helvetica, clean, sans-serif;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-mlmsg pre,
> #yiv8680019145
>
> code {
>
> font:115% monospace;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-mlmsg ∗ {
>
> line-height:1.22em;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-mlmsg #yiv8680019145logo
> {
>
> padding-bottom:10px;}
>
>
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-msg p a {
>
> font-family:Verdana;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-msg
>
> p#yiv8680019145attach-count span {
>
> color:#1E66AE;font-weight:700;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-reco
>
> #yiv8680019145reco-head {
>
> color:#ff7900;font-weight:700;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-reco {
>
> margin-bottom:20px;padding:0px;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-sponsor
> #yiv8680019145ov
>
> li a {
>
> font-size:130%;text-decoration:none;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-sponsor
> #yiv8680019145ov
>
> li {
>
> font-size:77%;list-style-type:square;padding:6px 0;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-sponsor
> #yiv8680019145ov
>
> ul {
>
> margin:0;padding:0 0 0 8px;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-text {
>
> font-family:Georgia;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-text p {
>
> margin:0 0 1em 0;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-text tt {
>
> font-size:120%;}
>
>
>
> #yiv8680019145 #yiv8680019145ygrp-vital ul li:last-child
> {
>
> border-right:none !important;
>
> }
>
> #yiv8680019145
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
> #yiv8856219972 #yiv8856219972 --
> #yiv8856219972ygrp-mkp {
> border:1px solid #d8d8d8;font-family:Arial;margin:10px
> 0;padding:0 10px;}
>
> #yiv8856219972 #yiv8856219972ygrp-mkp hr {
> border:1px solid #d8d8d8;}
>
> #yiv8856219972 #yiv8856219972ygrp-mkp #yiv8856219972hd {
> color:#628c2a;font-size:85%;font-weight:700;line-height:122%;margin:10px
> 0;}
>
> #yiv8856219972 #yiv8856219972ygrp-mkp #yiv8856219972ads {
> margin-bottom:10px;}
>
> #yiv8856219972 #yiv8856219972ygrp-mkp .yiv8856219972ad {
> padding:0 0;}
>
> #yiv8856219972 #yiv8856219972ygrp-mkp .yiv8856219972ad p {
> margin:0;}
>
> #yiv8856219972 #yiv8856219972ygrp-mkp .yiv8856219972ad a {
> color:#0000ff;text-decoration:none;}
> #yiv8856219972 #yiv8856219972ygrp-sponsor
> #yiv8856219972ygrp-lc {
> font-family:Arial;}
>
> #yiv8856219972 #yiv8856219972ygrp-sponsor
> #yiv8856219972ygrp-lc #yiv8856219972hd {
> margin:10px
> 0px;font-weight:700;font-size:78%;line-height:122%;}
>
> #yiv8856219972 #yiv8856219972ygrp-sponsor
> #yiv8856219972ygrp-lc .yiv8856219972ad {
> margin-bottom:10px;padding:0 0;}
>
> #yiv8856219972 #yiv8856219972actions {
> font-family:Verdana;font-size:11px;padding:10px 0;}
>
> #yiv8856219972 #yiv8856219972activity {
> background-color:#e0ecee;float:left;font-family:Verdana;font-size:10px;padding:10px;}
>
> #yiv8856219972 #yiv8856219972activity span {
> font-weight:700;}
>
> #yiv8856219972 #yiv8856219972activity span:first-child {
> text-transform:uppercase;}
>
> #yiv8856219972 #yiv8856219972activity span a {
> color:#5085b6;text-decoration:none;}
>
> #yiv8856219972 #yiv8856219972activity span span {
> color:#ff7900;}
>
> #yiv8856219972 #yiv8856219972activity span
> .yiv8856219972underline {
> text-decoration:underline;}
>
> #yiv8856219972 .yiv8856219972attach {
> clear:both;display:table;font-family:Arial;font-size:12px;padding:10px
> 0;width:400px;}
>
> #yiv8856219972 .yiv8856219972attach div a {
> text-decoration:none;}
>
> #yiv8856219972 .yiv8856219972attach img {
> border:none;padding-right:5px;}
>
> #yiv8856219972 .yiv8856219972attach label {
> display:block;margin-bottom:5px;}
>
> #yiv8856219972 .yiv8856219972attach label a {
> text-decoration:none;}
>
> #yiv8856219972 blockquote {
> margin:0 0 0 4px;}
>
> #yiv8856219972 .yiv8856219972bold {
> font-family:Arial;font-size:13px;font-weight:700;}
>
> #yiv8856219972 .yiv8856219972bold a {
> text-decoration:none;}
>
> #yiv8856219972 dd.yiv8856219972last p a {
> font-family:Verdana;font-weight:700;}
>
> #yiv8856219972 dd.yiv8856219972last p span {
> margin-right:10px;font-family:Verdana;font-weight:700;}
>
> #yiv8856219972 dd.yiv8856219972last p
> span.yiv8856219972yshortcuts {
> margin-right:0;}
>
> #yiv8856219972 div.yiv8856219972attach-table div div a {
> text-decoration:none;}
>
> #yiv8856219972 div.yiv8856219972attach-table {
> width:400px;}
>
> #yiv8856219972 div.yiv8856219972file-title a, #yiv8856219972
> div.yiv8856219972file-title a:active, #yiv8856219972
> div.yiv8856219972file-title a:hover, #yiv8856219972
> div.yiv8856219972file-title a:visited {
> text-decoration:none;}
>
> #yiv8856219972 div.yiv8856219972photo-title a,
> #yiv8856219972 div.yiv8856219972photo-title a:active,
> #yiv8856219972 div.yiv8856219972photo-title a:hover,
> #yiv8856219972 div.yiv8856219972photo-title a:visited {
> text-decoration:none;}
>
> #yiv8856219972 div#yiv8856219972ygrp-mlmsg
> #yiv8856219972ygrp-msg p a span.yiv8856219972yshortcuts {
> font-family:Verdana;font-size:10px;font-weight:normal;}
>
> #yiv8856219972 .yiv8856219972green {
> color:#628c2a;}
>
> #yiv8856219972 .yiv8856219972MsoNormal {
> margin:0 0 0 0;}
>
> #yiv8856219972 o {
> font-size:0;}
>
> #yiv8856219972 #yiv8856219972photos div {
> float:left;width:72px;}
>
> #yiv8856219972 #yiv8856219972photos div div {
> border:1px solid
> #666666;height:62px;overflow:hidden;width:62px;}
>
> #yiv8856219972 #yiv8856219972photos div label {
> color:#666666;font-size:10px;overflow:hidden;text-align:center;white-space:nowrap;width:64px;}
>
> #yiv8856219972 #yiv8856219972reco-category {
> font-size:77%;}
>
> #yiv8856219972 #yiv8856219972reco-desc {
> font-size:77%;}
>
> #yiv8856219972 .yiv8856219972replbq {
> margin:4px;}
>
> #yiv8856219972 #yiv8856219972ygrp-actbar div a:first-child {
> margin-right:2px;padding-right:5px;}
>
> #yiv8856219972 #yiv8856219972ygrp-mlmsg {
> font-size:13px;font-family:Arial, helvetica, clean,
> sans-serif;}
>
> #yiv8856219972 #yiv8856219972ygrp-mlmsg table {
> font-size:inherit;font:100%;}
>
> #yiv8856219972 #yiv8856219972ygrp-mlmsg select,
> #yiv8856219972 input, #yiv8856219972 textarea {
> font:99% Arial, Helvetica, clean, sans-serif;}
>
> #yiv8856219972 #yiv8856219972ygrp-mlmsg pre, #yiv8856219972
> code {
> font:115% monospace;}
>
> #yiv8856219972 #yiv8856219972ygrp-mlmsg ∗ {
> line-height:1.22em;}
>
> #yiv8856219972 #yiv8856219972ygrp-mlmsg #yiv8856219972logo {
> padding-bottom:10px;}
>
>
> #yiv8856219972 #yiv8856219972ygrp-msg p a {
> font-family:Verdana;}
>
> #yiv8856219972 #yiv8856219972ygrp-msg
> p#yiv8856219972attach-count span {
> color:#1E66AE;font-weight:700;}
>
> #yiv8856219972 #yiv8856219972ygrp-reco
> #yiv8856219972reco-head {
> color:#ff7900;font-weight:700;}
>
> #yiv8856219972 #yiv8856219972ygrp-reco {
> margin-bottom:20px;padding:0px;}
>
> #yiv8856219972 #yiv8856219972ygrp-sponsor #yiv8856219972ov
> li a {
> font-size:130%;text-decoration:none;}
>
> #yiv8856219972 #yiv8856219972ygrp-sponsor #yiv8856219972ov
> li {
> font-size:77%;list-style-type:square;padding:6px 0;}
>
> #yiv8856219972 #yiv8856219972ygrp-sponsor #yiv8856219972ov
> ul {
> margin:0;padding:0 0 0 8px;}
>
> #yiv8856219972 #yiv8856219972ygrp-text {
> font-family:Georgia;}
>
> #yiv8856219972 #yiv8856219972ygrp-text p {
> margin:0 0 1em 0;}
>
> #yiv8856219972 #yiv8856219972ygrp-text tt {
> font-size:120%;}
>
> #yiv8856219972 #yiv8856219972ygrp-vital ul li:last-child {
> border-right:none !important;
> }
> #yiv8856219972
>
>
>
>
>
>