Hi Andy,
I meant to say that MG section works in VCF and VCA mode but not in VCO mode. The synth itself plays fine but it is detuned without the possibility to be tuned. And yes, I am the person who was having problems with the board after it was repaired. But I would rather avoid dealing with that repairsman again.
Thanks,
Milan
--- In PolySix@yahoogroups.com, "Andrew Jury" <andy@...> wrote:
>
> Hi Milan,
>
>
>
> If the VCO has stopped working then it is no wonder there are problems with
> the tuning and mod wheel! Just remind me, were you the person who was having
> problems with the battery running flat on the '367 after it was repaired? I
> really think the guy who repaired this should really take a second look at
> it for you. If you want to have a go yourself take a look at the switching
> action at IC29 pin 11 and pin 13 of the comparator IC3. But I would address
> these issues before you start digging in the far left-hand corner of your
> P6!
>
>
>
> Cheers,
>
> Andy
>
>
>
>
>
> From: PolySix@yahoogroups.com [mailto:PolySix@yahoogroups.com] On Behalf Of
> Mekonin
> Sent: 30 November 2009 17:31
> To: PolySix@yahoogroups.com
> Subject: [PolySix] Re: Master tune + Mod wheels not working
>
>
>
>
>
> Hi Andy,
>
> ok so I tested the MG section. It works when put to VCF and VCO, but when
> it's on VCO it has no effect whatsoever.
>
> Milan
>
> --- In PolySix@yahoogroups.com <mailto:PolySix%40yahoogroups.com> , "Andrew
> Jury" <andy@> wrote:
> >
> > Hi Milan,
> >
> >
> >
> > Can you tell us if the MG section of your Polysix is in full working
> order?
> > Particularly the modulation routing switch (VCA, VCF, VCO)? This may have
> a
> > bearing on the problem if it is not.
> >
> >
> >
> > Thanks,
> >
> > Andy
> >
> >
> >
> > From: PolySix@yahoogroups.com <mailto:PolySix%40yahoogroups.com>
> [mailto:PolySix@yahoogroups.com <mailto:PolySix%40yahoogroups.com> ] On
> Behalf Of
> > Mekonin
> > Sent: 29 November 2009 09:48
> > To: PolySix@yahoogroups.com <mailto:PolySix%40yahoogroups.com>
> > Subject: [PolySix] Master tune + Mod wheels not working
> >
> >
> >
> >
> >
> > Hello fellow Polysix lovers,
> >
> > I am writing this in need of your help once again.
> >
> > Few weeks ago my P6 started acting funny, it was detuned down for a whole
> > octave and a half, and I noticed that master tune knob and mod wheels have
> > no effect on the sound. I opened it up, saw if there are any loose cables,
> > put it in test mode and back again, and when I returned it to "Normal", it
> > was working as it should. But next time I powered it on (or the second
> time
> > I can't remember), after some playing I noticed that the pitch was
> drifting.
> > I tried the tune knob and mod wheels and realised that they are not
> working
> > like that time before. This time, fiddling inside the P6 did not help.
> > If you have any suggestions what might be the problem, please write.
> >
> > Thank you all in advance,
> > Milan
> >
> >
> >
> >
> >
> > [Non-text portions of this message have been removed]
> >
>
>
>
>
>
> [Non-text portions of this message have been removed]
>