I have no idea where to get the chips... Maybe there is some old
electronics supply house in a near-by villa that has a tube of them..
If you do find a tube and at decent price, I suggest you buy the whole
tube. Then you can sell your extras to us and make a handy profit.
Otherwise.... Figure out what you need, and post to this list. And of
course check ebay.
On 5/26/07, blacknred123 <blacknred123@yahoo.co.uk> wrote:
> Hi yes it seems that your spot on!! It is infact 1 dodgy ssmt 2056
> chip and could there be possibly one ssmt 2044 above as it seems the
> working chip even swapped for the bad still is a bit muffled on that
> unit!! once i started removing the chips (ssmt 2056) the problem did
> follow!! Now I'm
> really desperate do you know where i could get the said chips from!??!
> Many thanks for your help i would have been totally stuck without your
> help!!
>
> --- In PolySix@yahoogroups.com, "Chromatest J. Pantsmaker"
> <chromatest@...> wrote:
> >
> > I think those chips are all socketed, so you could ∗∗∗CAREFULLY∗∗∗
> > swap the chips around and see if the problem follows. When you open
> > the case, you can tell which voice is sounding by the LED. Find out
> > which one is bad, then swap it with another.. One chip at a time.
> >
> > Make sure the system is turned off for a couple minutes before you
> > pull or insert a chip. The chips used are not easy to get, but
> > possible.
> >
> > On 5/25/07, blacknred123 <blacknred123@...> wrote:
> > > Hi firstly thanks for your reply secondly do you think its easily
> > > sorted i.e. is there much chance of me picking up an EG chip for
> > > replacement assuming that is the problem!?!?
> > >
> > >
> > >
> > > --- In PolySix@yahoogroups.com, klosmon <klosmon@> wrote:
> > > >
> > > > First impression is that one of the envelope generators is not
> > > working.
> > > > Possibly the EG chip itself; possibly the support circuit.
> > > >
> > > > ~G
> > > >
> > > > At 06:49 AM 5/25/2007, you wrote:
> > > >
> > > > >Hi all I just recieved my polysix aware that it had a problem it
> > > seems
> > > > >that every 6th note i play no mater where it is on there board it
> > > cuts
> > > > >out, But only in poly mode. The key does not sound when i have the
> > > > >switch set to eg on the VCA but when switched to wave on the vca
> > > the
> > > > >sixth note whatever it may be is muffled. Does anyone have any
> > > > >ideas!?! Bearing in mind that the batt has never been changed i
> > > > >wodered if this may have something to do with it though all buttons
> > > > >lights etc work as they should!??!......will be changing batt this
> > > week!
> > > > >
> > > > >
> > > >
> > > >
> > > > [Non-text portions of this message have been removed]
> > > >
> > >
> > >
> > >
> > >
> > > PolySix "Digiest" Page: http://www.acc.umu.se/~amber/Poly6
> > > Yahoo! Groups Links
> > >
> > >
> > >
> > >
> >
> >
> > --
> > .sig
> > -Chromatest J. Pantsmaker
> > http://www.chromatest.net
> >
>
>
>
>
> PolySix "Digiest" Page: http://www.acc.umu.se/~amber/Poly6
> Yahoo! Groups Links
>
>
>
>
--
.sig
-Chromatest J. Pantsmaker
http://www.chromatest.net