No, I would say it is the same code. Are you certain that you flashed all three sysex blocks of the firmware?
My RemoteSL25 does the same thing your controllers do. It sends NRPN's based upon what has changed since the last NRPN message. So if the MSB and LSB are the same as before then only the data message gets sent. If the LSB changes then it will send the LSB and then the data. If the MSB changes then it will send that then data. And finally, if MSB and LSB are both different then they all get sent.
HAWK responds correctly to all of the above.
I also ran tests using amidi on LINUX as follows:
################################################################################
# list midi devices
################################################################################
amidi -l
################################################################################
# send NRPN with MSB=0, LSB=18 (24d=VCF cutoff) and data Min,Mid,Max
# send MSB,LSB,Data a few times then send data values only
################################################################################
amidi -S "B0 62 18 B0 63 00 B0 06 00" -p hw:3,0,0
amidi -S "B0 62 18 B0 63 00 B0 06 6F" -p hw:3,0,0
amidi -S "B0 62 18 B0 63 00 B0 06 7F" -p hw:3,0,0
#WORKS AOK
################################################################################
# send NRPN data change only
################################################################################
amidi -S "B0 06 00" -p hw:3,0,0
amidi -S "B0 06 7F" -p hw:3,0,0
amidi -S "B0 06 00" -p hw:3,0,0
# WORKS AOK
################################################################################
# send NRPN with LSB=18 (24d=VCF cutoff) MSB=0, and data Min,Mid,Max
# send LSB,MSB,Data a few times then send data values only
################################################################################
amidi -S "B0 63 00 B0 62 18 B0 06 00" -p hw:3,0,0
amidi -S "B0 63 00 B0 62 18 B0 06 6F" -p hw:3,0,0
amidi -S "B0 63 00 B0 62 18 B0 06 7F" -p hw:3,0,0
################################################################################
# send NRPN data change only
################################################################################
amidi -S "B0 06 00" -p hw:3,0,0
amidi -S "B0 06 7F" -p hw:3,0,0
amidi -S "B0 06 00" -p hw:3,0,0
# WORKS AOK
################################################################################
# send NRPN with LSB=18 (24d=VCF cutoff) MSB=0, and data Min,Mid,Max
# send MSB,LSB,Data then send LSB,data only to change two parameters
################################################################################
# send full VCF change
amidi -S "B0 63 00 B0 62 18 B0 06 00" -p hw:3,0,0
# send DCO1 octave change to "3" as LSB,data only
amidi -S "B0 62 00 B0 06 7F" -p hw:3,0,0
# send DCO1 octave change to "1" as LSB,data only
amidi -S "B0 62 00 B0 06 00" -p hw:3,0,0
# WORKS AOK
################################################################################
# send NRPN data change only
################################################################################
amidi -S "B0 06 00" -p hw:3,0,0
amidi -S "B0 06 7F" -p hw:3,0,0
amidi -S "B0 06 00" -p hw:3,0,0
# WORKS AOK
So this must be quite frustrating but I am sure we'll figure it out.
Try to flash all three version 2.5.7 files again.
Mike
On Monday, May 12, 2014 6:42 PM, "bperkins211@... [korgpolyex]" <korgpolyex@yahoogroups.com> wrote:
I checked my HAWK and it indeed does have v2.57 installed.My guess is that is the same code you just posted up.. unless it's a 2.57b?Any other ideas? I'd even send you this Evolution controller to use for testing, since I'm sure if you get it working, all the others will work too.