After doing some tests, I think it may be a bad pitch bend slider as someone suggested, since the more I moved/worked it, the bending began to work. What is the pitch bend range of the poly 800 at the highest setting? Currently it goes from C up to G and C down to F.
-Frank
--- In korgpolyex@yahoogroups.com, no freq <no.freq@...> wrote:
>
> Hi,
>
> I once noticed this kind of problem on one of the poly-800 I serviced. And
> from what I can recall, I had to change a varicap for which I've been able
> to source an equivalent at Farnell.
>
> Looking at the schematic, it seems like there's only one, labeled VC1, in
> "block 19".
>
> Hope it helps...
>
> Good luck!
>
> 2012/2/17 F Aitken <mfaitkenjr@...>
>
> > ∗∗
> >
> >
> > To everyone replying, I appreciate your help. I will do further testing
> > and examination this weekend. Any other ideas are welcome. If the service
> > manual in not in the "File" section, can someone email it to me or direct
> > my to a link. Thanks again! -Frank
> >
> > ∗From:∗ Martin Ator <cyllall@...>
> > ∗To:∗ "korgpolyex@yahoogroups.com" <korgpolyex@yahoogroups.com>
> > ∗Sent:∗ Friday, February 17, 2012 10:16 AM
> >
> > ∗Subject:∗ Re: [korgpolyex] DCO and VCF of Joystick work, but not Pitch
> > Bend
> >
> >
> > If you use a MIDI monitor like MIDIOX from the poly 800 you should be
> > able to transmit pitch bend data and see it being received,you can try to
> > send pitch bend to the poly 800 as well.
> > You can check for cracks in the solder and broken wires inside behind the
> > joystick mechanism.
> > If it is transmitting MIDI then you need to try the calibration routine in
> > the service manual. You only need a multimeter and someone to wiggle your
> > stick.
> > Page 21 section 2 D/A converter check and adjustment would be a good place
> > to start.
> >
> > ∗From:∗ F Aitken <mfaitkenjr@...>
> > ∗To:∗ "korgpolyex@yahoogroups.com" <korgpolyex@yahoogroups.com>
> > ∗Sent:∗ Friday, 17 February 2012, 13:11
> > ∗Subject:∗ Re: [korgpolyex] DCO and VCF of Joystick work, but not Pitch
> > Bend
> >
> >
> > Hi, Thanks for the reply. Yes, I've moved the Bend slider to max and it
> > doesn't work. I need to test the pitch bend controlling the Poly from
> > another synth. I hope the issue is no more than a good joystick cleaning
> > or replacement.
> > -Frank
> >
> > ∗From:∗ Martin Ator <cyllall@...>
> > ∗To:∗ "korgpolyex@yahoogroups.com" <korgpolyex@yahoogroups.com>
> > ∗Sent:∗ Friday, February 17, 2012 4:37 AM
> > ∗Subject:∗ Re: [korgpolyex] DCO and VCF of Joystick work, but not Pitch
> > Bend
> >
> >
> > Silly question but, have you adjusted the 'BEND' slider next to the
> > volume control to maximum (10) the pitch bend wont work without this. I
> > always forget about this one myself.
> >
> > Martin
> >
> > ∗From:∗ MFAitkenJr <mfaitkenjr@...>
> > ∗To:∗ korgpolyex@yahoogroups.com
> > ∗Sent:∗ Friday, 17 February 2012, 3:19
> > ∗Subject:∗ [korgpolyex] DCO and VCF of Joystick work, but not Pitch Bend
> >
> >
> > Hi, I have a poly 800 and the joystick half works. The DCO and VCF of
> > Joystick work, but not Pitch Bend. Is this an easy fix? Or is the joystick
> > just not good anymore? I opened it up and all the cables seem to be
> > connected fine. If the joystick assembly is broken, does anyone know where
> > I can buy it?
> >
> > Thanks,
> > Frank
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
>