Archive of the former Yahoo!Groups mailing list: Modular Synth Panels

previous by date index next by date
previous in topic topic list next in topic

Subject: Re: [ModularSynthPanels] Re: bananalogue vcs in motm format?

From: Ross Stapf <pristak@...>
Date: 2009-10-01

I've built one.  I have another half finished.  The only problem is the led's.  http://www.electro-music.com/forum/topic-26503-25.html Look at this thread, page 2 about half way down is when the MOTM version is discussed.  There is a part list for the euro version on page 1 that I used and it was right for the most part.
 
It is well labeled and was pretty easy to build.  Again see the instructions Andrew F posted to fix this.  Other folks mention a problem with the euro boards.  I did not have this issue.  The only problem I had was with the LED's and the fix Andrew F gave works just fine.
 
This was the first project I did without step by step instructions.  I had been doing diy for less than a year when I finished it.  I used Sduck's panel layout.
 
Ross
 

--- On Thu, 10/1/09, adaaxs <wonggster@...> wrote:

From: adaaxs <wonggster@...>
Subject: [ModularSynthPanels] Re: bananalogue vcs in motm format?
To: ModularSynthPanels@yahoogroups.com
Date: Thursday, October 1, 2009, 9:02 AM

 
I got a single board unit from Seth marked bano4ro with just an MOTM power connector.
They were well done , they had anchor holes for the shield on coax hookup wire.

The doc for this board is limited. Do you have any ?

best

gino

>
> Sounds about right, except I've only got 10 jacks, and a hole for the led. Which boards are you using - the cgs ones? I used ones I got from Seth, which I think were prototypes of the cgs ones - the led didn't work as labeled, and the bipolar out was an add-on optional part. There were holes for pcb mount pots - I don't know if the cgs boards have those.
>
> --- In ModularSynthPanels@ yahoogroups. com, "adaaxs" <wonggster@> wrote:
> >
> >
> > I have a Mac too, so before I go build a pc. Seth didn't point me to any doc on this board so I have been winging it. According to my best guess a panel should be cut for 4 pots, 1 dpdt toggle and 11 jacks and I wouldn't be surprised if I was wrong.
> >
> >
> >
> > >
> > > thanks much.
> > >
> > > is the picture in the photos section accurate? i can't currently get
> > > my Parallels installation to work, so i can't fire up FPE to check
> > > layout etc.
> > >
> > > tx
> > > j
> > >
> > >
> > > >updated verson posted to files section in sduck panels
> > > >
> > > >--- In ModularSynthPanels@ yahoogroups. com, "sduck409" <sduck409@> wrote:
> > > >>
> > > >> Look in the sduck folder in the files section. 2u, fully featured,
> > > >>not trad but you can easily modify it. Before ordering it give me a
> > > >>chance to make sure I upped the revised version - I messed up the
> > > >>position of the jacks on my first design of this, and revised it,
> > > >>but don't remember if I ever posted the revision. I'll check that
> > > >>this evening. There may be pictures of this one also in the
> > > >>pictures section.
> > > >>
> > > >> --- In ModularSynthPanels@ yahoogroups. com, Jason Proctor <jason@> wrote:
> > > >> >
> > > >> > does anyone have a good FPD for a (2U, one presumes) MOTM format
> > > >> > Bananalogue VCS?
> > > >> >
> > > >> > thanks much
> > > >> >
> > > >>
> > > >
> > > >
> > > >
> > > >
> > > >----------- --------- --------- -------
> > > >
> > > >Yahoo! Groups Links
> > > >
> > > >
> > > >
> > >
> >
>