Hi John,
Where do you get the PVC, other then a "plastics" store? Anything I
missed? I think there is a TAP plastics in San Jose, CA.
The 'L' picks up two edges of the PCB? Do you flycut the PVC flat
first? should true it up.
I have a 60 degree engraving bit that was recommended to me.
Yeah, getting two traces between pads is a little hard to achieve! I'll
settle for a single trace. I've seen their sample boards, really nice.
Are you saying that they use thinner copper or a special board for
mechanical etching? I hadn't heard that.
Alan KM6VV
crankorgan wrote:
>
> Hi Alan,
> I mount a 8" X 8" piece of 1/4" PVC to my bed
> using four flat head 10-32 bolts. I run the machine with
> an old Mechanical Etching bit in it. I cut a fine "L" in
> the plastic. In the "L" I drill and tap 2-56 bolt holes.
> I then place a PCB under the bolt heads. This helps me
> locate where the other screws go.
> The board is held down on all sides with just the
> bolt heads. If you use a 60 degree Mechanical Etching bit
> variations in copper and board will not be a problem. This
> is if the board is cuped up! The single sided ones I buy
> are.
> My machine will do a trace between a pad. Two traces
> between a pad!!! No way! I have seen the sample boards on
> those site. Show me the boards made by regular people using
> their machine. No burrs either, just perfect traces.
> The boards I use have very thick copper. If I get
> the money, I will try some PCB made for Mechanical Etching.
>
> John
>
> --- In Homebrew_PCBs@y..., Alan Marconett KM6VV <KM6VV@a...> wrote:
> > Hi John,
> >
> > Good tips! When you bolt your boards down, how much deviation is
> left?
> > I just looked at LPKF (again, for the 1000th time), and they are
> VERY
> > precise! TWO traces between pads. And I'm thinking that if the
> depth
> > is controlled more closely, bit life will be improved.
> >
> > Alan KM6VV
> >
> >
> > crankorgan wrote:
> > >
> > > Hi Alan,
> > > I see that! I use the heads of 2-56 bolts to hold
> > > my boards down. The ones I buy are cuped foil side up. They
> > > are 4" X 6". The bolts go into a piece of 1/4" PVC. I find
> > > holding the board by the edge-the best method so far. Since
> > > all my boards are 4" X 6" I only have to take two bolts out
> > > and the board slides out the end. The bolts pull the board
> > > down flat. When I do smaller boards, I have other rows of
> > > taped holes in the PVC. The Tit4Tat board was 1/2 of the
> > > 4" X 6" board. I would make two at once. I used to make 4
> > > 1 axis boards out of one 4" X 6". Tape is fine for doing
> > > a flat pcb, but most surplus boards come warped.
> > > How would I fix a warped board when making a double
> > > sided board? Simple, use one or two bolts in the middle of the
> blank.
> > > They then become mounting holes.
> > >
> > > John
> > >
> > > --- In Homebrew_PCBs@y..., Alan Marconett KM6VV <KM6VV@a...>
> wrote:
> > > > Hi Listies,
> > > >
> > > > Some activity on the CCED list about LPKF and holding PCB's
> down to
> > > mill
> > > > them. Anyone here have the LPKF system?
> > > >
> > > >
> http://www.lpkfusa.com/products/product/rapidpcbpro/index.htm
> > > >
> > > > I'd like to get a closer view of the Z height "tracking donut"
> on
> > > this
> > > > machine. And, I'm in the process of downloading a demo of their
> > > > program.
> > > >
> > > > Alan KM6VV
> > > > P.S. I'm also looking at a low-cost Gerber to Gcode translation
> > > program
> > > > that should be available soon! More details when past beta.
> > >
>
>
> Be sure to visit the group home and check for new Bookmarks and files:
> http://groups.yahoo.com/group/Homebrew_PCBs
>
> To unsubscribe from this group, send an email to:
> Homebrew_PCBs-unsubscribe@yahoogroups.com
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/