yup, pretty much what Jeremy said. dont use busses. go ahead and
delete the busses you made.
nets can be a bit tricky to actually get connected. Run the ERC
(engineering? rule check) to see if you have any unconnected
pins/nets. Its easy to actually not make the connection. erc will
tell you if you have any.
when you switch to board view, you will see all your components
sitting outside the board outline. You'll have to move them inside
the outline before you can do anything.
In general, I only use autorouting to get a sense of how good my
component placement is. The autorouter is kind of stupid and will
often rout the worst possible net first so you need to give it a lot
of guidance. I'll autorout, ripup, move components, try it again
until I can get pretty far. Then I ripup all and start manually
routing. It may take some time but you will start getting a sense of
the best placement and rotation of a device.
When you are done with routing, you really aren't done. You will
need to run DRC (design rule checking) to ensure that your component
placement and routing is good. dont be dismayed if you get a lot of
DRC errors.
--- In
Homebrew_PCBs@yahoogroups.com, "Jeremy Taylor" <jeremy@e...>
wrote:
> You have to place the components on the board, then run the
autorouter. It will not place components for you, thus it can not
autoroute till you do so. It will put all the components that you use
in your schematic, on the board page, but they will all be off to the
side grouped together, yet connected by the air wires you specified
in the schematic. .
> I find it very useful to name all related components and name the
nets in the schematic so it's easier to tell which resistor goes with
which cap when you start laying out the board.
> I never use "buses" in the software, I just use airwires, that get
called nets. IMO a trace is a trace whether it be a bus or a net.
>
> http://www.soundclick.com/jtsound
> ----- Original Message -----
> From: teilhardo
> To: Homebrew_PCBs@yahoogroups.com
> Sent: Sunday, May 16, 2004 11:03 PM
> Subject: [Homebrew_PCBs] Re: New to group and first attempt at PCB
>
>
> So, if I put nets together with my components, and then switch to
> layout editor, isn't the program supposed to logically come up
with a
> layout?
> In my schematic, I connected the components together using these
> "buses" and then some pop up error came up and said that they
need to
> be connected using nets. So I put the nets on top of the busses,
is
> this right? Or do I only need nets OR busses?
> Thanks,
> Tei
> --- In Homebrew_PCBs@yahoogroups.com, "Phil" <phil1960us@y...>
wrote:
> > a net in eagle is a number of pins that are electically
connected
> > together - kind of the way you would logically think of it. It
has a
> > name. You dont have to actually draw them as connected. Any
nets
> > you name Gnd, for example, will be connected together. This
is
> > great for doing a schematic with out making a wiring mess in
the
> > drawing. I use it all the time.
> >
> > A bus is a set of parallel nets with a common name, say "Bus",
and
> > each net has a sub name - Bus1, Bus2, Bus3... Its used mainly
for,
> > shock!, creating busses and keeping them tidy on the schematic.
> >
> > --- In Homebrew_PCBs@yahoogroups.com, "Leon Heller"
> > <leon_heller@h...> wrote:
> > > ----- Original Message -----
> > > From: "teilhardo" <teilhardo@y...>
> > > To: <Homebrew_PCBs@yahoogroups.com>
> > > Sent: Sunday, May 16, 2004 9:38 PM
> > > Subject: [Homebrew_PCBs] Re: New to group and first attempt
at PCB
> > >
> > >
> > > > Eagle has some nice ULP's but it is sort of awkward. Does
anyone
> > know
> > > > the difference between a "bus" and a "net"?
> > >
> > > With the Pulsonix software I use, a bus contains several nets.
> > >
> > > Leon
> > > --
> > > Leon Heller, G1HSM
> > > http://www.geocities.com/leon_heller
>
>
>
> Be sure to visit the group home and check for new Bookmarks and
files:
> http://groups.yahoo.com/group/Homebrew_PCBs
>
>
> Yahoo! Groups Sponsor
> ADVERTISEMENT
>
>
>
>
>
> --------------------------------------------------------------------
----------
> Yahoo! Groups Links
>
> a.. To visit your group on the web, go to:
> http://groups.yahoo.com/group/Homebrew_PCBs/
>
> b.. To unsubscribe from this group, send an email to:
> Homebrew_PCBs-unsubscribe@yahoogroups.com
>
> c.. Your use of Yahoo! Groups is subject to the Yahoo! Terms of
Service.
>
>
>
> [Non-text portions of this message have been removed]