Hi Adam
Sorry for the late reply - terribly busy times here.
>Thanks for the descriptions. What are the internal
>dimensions of the tanks.
They are made to contain 2 and 4.5 liters respectively with a certain
"security" zone so as I don't have to fill them completely up. The
dimensions are therefore 4x25x29 cm with side pannels sized 9x30. The
bigger tank is identical except that it's 9 cm wide. All these
measures are internal dimesions.
>From your web pages I can see 4
>smaller ones and one larger one for the copper
>electroplating. From your pictures the tanks look like they
>were made from 3 mm sheet.
Uhmmm they are actually just 2mm :)
>Did you consider putting an outer
>lip on the tops of the tanks ?
Yes, but it turned out that it's not necesairly needed. I WILL replace
the tanks though but mostly only because I want to try to build them
with a faster & easier method. I'm thinking of makeing the side
pannels from 4mm sheets and then mill a "U shaped track" into them
where I can sink the 'U' formed sheets into. This should make the
welder process easier and also make it more rigid. An outer lip seems
like a good idea.
I must say that I like the fact that the tanks are "clear". You can
see a lot better what's going on and of course if a tank should ever
start to leak this would be seen much faster.
My "next generation" tanks also will have a tube inside that allows to
pump the liquid out of the tanks into a dedicated bottle per bath.
Like this I can further minimize that something happens to the
chemicals, overall, keep them cleaner and also avoid that parts of the
liquids vaporize. Especially the cleaning bath (#1) and also the
activator bath (#4) show this tendency. Well, #1 is really almost
behaves like water. Luckyly this is also the cheapest bath.
I definately will try this milling thing as soon as my CNC drilling
machine gets ready. The material is all ready for long (you may can
imagine how hot I am to start puting it together) but as mentioned,
terribly busy times here. I'm working 18+ hours at 7 days for now 9
months or so.. Luckyly there is meanwhile a silver stripe on the
horizon.
>I found that using lots of spring clamps are VERY helpful
>when welding. I clamp a large piece of chipboard to the
>bench so it hung out about 40 cm, I then could do all my
>work on this board and easily clamp things from underneath
>using sliding G clamps.
Hmmm, I unfortunately don't understand english good enough to know
what you mean. If you could make a picuture of that process I'm sure
it would become much clearer.
Markus
>Markus Zingg wrote:
>> Hi Adam
>>
>>
>>>I can see the 3 mm sheet being bent that way say upto 300 mm
>>>in length. I made a plastic bender because I was planing on
>>>doing larger tanks 450 mm length on 4.5mm thick PVC. You
>>>seem to have done things quite nicely with what you've got.
>>>
>>>What thickness material are you using ?
>>
>>
>> 2mm and 4mm.
>>
>>
>>>Did you have to reinforce all the welding zones with blocks
>>>of wood before you started welding so that the "hobby glass"
>>>sheets didn't bend under the heat ?
>>
>>
>> They too bend under heat. What I did was first (using the 9mm reducion
>> nozzle) bend a long sheet (25x65cm) to a 'U' shape. I did this by
>> first bending one side, placing the sheet on a table into a 90degree
>> angle and let it cool out, then bend the second side. I thereafter
>> palced a thick wood block on the table as a base (in order to prevent
>> burning the table) and also created a little peace of wood that fit's
>> into the 'U' measuring ~4.5cm x 3cm using 5mm think wood. I then could
>> put the 'U' onto the side part (9x30cm) and place the wood into the
>> 'U' to prevent it from loosing shape. I then used one hand to hold the
>> 'U' down and also feed the plastic into the welder (of course this
>> time unsing the welding nozzle) and the other to hold the hot air gun.
>> It takes some practice but onece you figured it out it works not that
>> bad. You somehow miss a third hand :))
>>
>>
>>>I found that I had to make special wooden frame inserted
>>>into the tank so that during welding the pressure of the
>>>welding rod didn't collapse the sheets.
>>
>>
>> See above, you probably did the same thing then.
>>
>>
>>>From your past posts on the "hobby glass" I get the feeling
>>>this is ridged clear pvc sheeting. Try burning some and see
>>>how it compares to flame color/smoke smell to some real PVC.
>>>PVC is very difficult to get burning by its self and
>>>produces a harsh smelling smoke, (HCl fumes).
>>
>>
>> I'm currently not at home, so can't try this right away. I happen to
>> know how PVC smells when burning. Some 22 years ago I happend to learn
>> tool maker as my first profession where we were building molds to
>> fabricate plastic parts. I have a collection of the diverse plastic
>> base materials somewhere. Have to grab that out and compare the
>> flames/fumes of them with the glass I'm using.
>>
>> Markus
>>
>>
>> Be sure to visit the group home and check for new Bookmarks and files:
>> http://groups.yahoo.com/group/Homebrew_PCBs
>>
>> To unsubscribe from this group, send an email to:
>> Homebrew_PCBs-unsubscribe@yahoogroups.com
>>
>>
>>
>> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>>
>>
>
>
>
>Be sure to visit the group home and check for new Bookmarks and files:
>http://groups.yahoo.com/group/Homebrew_PCBs
>
>To unsubscribe from this group, send an email to:
>Homebrew_PCBs-unsubscribe@yahoogroups.com
>
>
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>