Thanks to all who replied to my question. I'll investigate the all the suggestions.
73's
Steve
----- Original Message -----
From: Harvey White
To: Homebrew_PCBs@yahoogroups.com
Sent: Thursday, May 22, 2008 8:30 PM
Subject: Re: [Homebrew_PCBs] H2O2 + muriatic acid etchant?
On Thu, 22 May 2008 19:08:29 +0100, you wrote:
>Hello Group,
>
>I've been following this discussion with interest and would like to move away from etching pcb's with ferric chloride.
>I live in the UK and wonder if anyone knows of a supplier of the muriatic acid and hydrogen peroxide to home users. My local chemist was no help at all and didn't have a clue.
Home supply stores often have muriatic acid (HCl) for pool cleaning
supplies. However, the last time I was in the UK, I noticed a
suspicious lack of such things. You might find it used for cleaning
concrete or bricks, though.
If you have a Walmart or equivalent, you might find hydrogen peroxide
sold in largish quantities as a disinfectant. It is also possibly
available from beauty supply stores in a higher concentration.
Harvey
>Any help greatly appreciated!
>
>Steve
> ----- Original Message -----
> From: Michel Baguet
> To: Homebrew_PCBs@yahoogroups.com
> Sent: Tuesday, May 20, 2008 5:05 PM
> Subject: Re: [Homebrew_PCBs] H2O2 + muriatic acid etchant?
>
>
> I'm using HCl for a years. 700cc of distilled water, 270cc of HCl highly concentrate (you can see smoke when the bottle is open) and 30cc of H202 at 30% concentration.
> The only problem with this etchant is that H2O2 decompose with heat and light and if you etch another board a few days later, you don't know what part of H2O2 is still in solution. So I put the board to etch in the tank and take it out to see the color of the copper. If there is still enough H2O2, it must turn brown immediately.
> If not, I add 10cc and son on but never more than 30cc (obvious !).
> But the cost of HCl, H2O and H2O2 is so cheap that I often replace the etchant, to always get accurate results with small traces. A 200cm² double sided board with 35µ copper take between 4 to 6 min. in bubble etch tank @ 45°C.
>
> clintonlcorbin <clcorbin@...> wrote: Folks,
>
> First, I want to say "Hi". I just recently started making my own
> single and two sided PCBs and even more recently joined the group.
> There is a lot of great info here!
>
> The question I have regards the etchant I have been using: 1 part
> muriatic acid and 2 parts H2O2 (hydrogen peroxide). I found the
> formula on a web page about (what else) DIY PCBs. As I was wanting to
> try making my own PCBs and the materials were easy to obtain and low
> cost, I decided to give it a try.
>
> All in all, I have been quite happy with the results so far. I
> haven't tried any real fine line etching yet and the smallest SMD
> devices are 0603, so they are pretty big. The etchant is clear, so it
> is very easy to keep your eye on the board during the etching process.
> Plus, I have been doing all my etching at room temperature with no
> heating at all. It generally takes about three minutes to fully etch
> the small (2x3" are the largest so far) boards I am working with.
>
> So the questions are:
>
> 1) How does this etchant compare to more traditional etchants?
> 2) Does it have over etch / under etch issues with finer lines?
> 3) Anything else I should be aware of?
> 4) Anyone else used this etchant along with the others that can give
> a pros/cons?
>
> Thanks for the help and all the info in this group.
>
> Clint
>
>
>
>
>
> [Non-text portions of this message have been removed]
>
>
>
>
>
>
>----------------------------------------------------------
>
>
> No virus found in this incoming message.
> Checked by AVG.
> Version: 7.5.524 / Virus Database: 269.23.21/1455 - Release Date: 19/05/2008 17:04
>
>
>[Non-text portions of this message have been removed]
------------------------------------------------------------------------------
No virus found in this incoming message.
Checked by AVG.
Version: 7.5.524 / Virus Database: 269.24.0/1459 - Release Date: 21/05/2008 17:34
[Non-text portions of this message have been removed]