Tony Smith wrote:
>>> There was a thread about it a while back (A year? More?).
>>>
>>> Track down Tom Gootee's page, I think it was him who tried
>>>
>> it. Might
>>
>>> be some results there.
>>>
>>> Apparently it's a bit hard to apply enough pressure.
>>>
>> Clamping causes
>>
>>> distortion, so you get pressure in one spot but not another, etc.
>>> Dumping weights on top didn't seem to help either.
>>>
>>> Tony
>>>
>>>
>>>
>> I use a heat press of sorts ... I make small PCB's no larger
>> than 3x4 inches ... I have a 4x6x1 inch piece of steel ... I
>> took a piece of aluminum oxide abrasive paper (8x10 inch)
>> laid it flat on the top of my table saw and dragged the steel
>> plate back and forth across the abrasive paper until it was
>> flat and shiny (I actually made a motor driven fixture to do
>> the dragging in a random fashion for me ... it took several
>> days and several sheets of abrasive) ... I use a hot plate to
>> heat the steel plate until it is the temp I want (usually 350
>> to 400 degrees F) using a thermocouple attached to the steel
>> plate to measure the temp ... I have ready a flat wooden
>> surface that has the blank PCB/laser image/plane paper ready
>> to receive the hot steel plate ... I place the steel plate on
>> the top cover paper and clamp the steel plate with about 300
>> pounds of pressure (about 25 pounds per square inch) using a
>> wide mouth vice grip pliers (this is moderate pressure ...
>> you can easily get 400 to 500 pounds of pressure) ... I leave
>> it clamped for about 1 minute then off to the water soak ...
>> I get good resolution and consistent results ... the flat
>> surface insures an even distribution of pressure ... the
>> thick steel plate holds the heat and won't distort under the
>> moderate pressures and temps used ...
>> Jim KI6MZ
>>
>
>
> Sounds like you've got too much time on your hands, you need a hobby :)
>
If you are going to do a process several times, you will always spend
LESS total time if you take the time up front to build the proper tools
... the steel I used was a mill "cut-off" so it had some ripples in it
... if the steel had been cut when the steel was cool, the lapping would
be done in 30 to 90 minutes
> I can't remember what the original thread was about, but it was something
> like a clothes press. I guess a lot of people start eyeing the sandwich
> maker in their kitchen as well...
>
> That chunk of steel you have won't bend easily, one problem solved. How
> long does it take to heat up? Obvious for making a batch it'll be faster
> than a laminator, but for one-offs?
>
It takes about 10 minutes from room temp the first use ... I always
allow the temp to over-shoot by about 20 degrees then set the steel
block on a narrow strip of wood ... when the temp comes back down to the
target i use it ... the thermocouple is on the top of the steel so
there is a temp gradient across the steel
> So for double sided you just flip the board over afterwards?
>
I do one side at a time ... I spray paint side 2 .. image transfer and
etch side 1 ... then spray paint side 1 ... image transfer and etch side
2 ... I do drill alignment holes for registration
> (BTW, gluing the sandpaper to a sheet of glass works well for lapping stuff,
> in case you don't have a cast iron table saw handy. Glass is very flat.)
>
> Tony
>
>
>
> Be sure to visit the group home and check for new Links, Files, and Photos:
> http://groups.yahoo.com/group/Homebrew_PCBs
>
> If Files or Photos are running short of space, post them here:
> http://groups.yahoo.com/group/Homebrew_PCBs_Archives/
> Yahoo! Groups Links
>
>
>
>
>
>