previous by date | index | next by date |
topic list |
>--
> This is really weird. Under "SCENE," 1 is Mod Dpt., 2 is Breath. I just
> couldn't get it to work, so I finally set it to "2:breath," and I was able
> to morph scenes with the Mod wheel. Can someone tell me what's going on?
>
> Thanks,
> -Joon
>
> ----- Original Message -----
> From: Edwards, Ed <ed.edwards@...>
> To: <AN1x-list@egroups.com>
> Sent: Friday, May 05, 2000 11:25 AM
> Subject: RE: [AN1x-list] Introduction
>
> > You need to go to the Utility Control Assign in the matrix and assign
> SCENE
> > to MW.
> >
> > There are 2 inherent insanities about this:
> > 1. Unless the on-board control is assigned to a function, external midi
> > won't control it. Example - if the mod wheel is not assigned to
> modulation,
> > the AN will not respond to an incoming CC1 message (mod wheel).
> > 2. People have uploaded banks of patches all over the web that mess up the
> > default Control Assignments. (and other stuff like midi channels, device
> #,
> > whatever) For instance, there are banks where no parameters are assigned
> to
> > any of the 8 knobs. Why someone would disable all of this control makes
> no
> > sense to me.
> >
> > I was making the mistake of using .syx files and loading banks which
> trashed
> > my control assignments. Then I came to my senses and started using the
> AN1x
> > editor. I'd load a bank to the editor, choose a patch on the AN I could
> > overwrite, then double click on the patches in the editor one at a time.
> > That way, only the patch data comes in to the AN. It's a safe way of
> > auditioning sounds.
> >
> >
> > Here's the excerpt from the manual about the control assignment function:
> >
> > Based on settings in the Control Assign function as well as
> > in the Control Matrix, you can use a single controller to
> > control one parameter of the internal tone generator and
> > another parameter of an external MIDI device, both at the
> > same time. It also lets you determine which device (MW,
> > FC, etc.) to use for Scene Control (see page 20).
> > Controllers which can be assigned using the UTILITY
> > SETUP Control function:
> > MW - Modulation Wheel
> > FV - Foot Volume
> > FC - Foot Controller
> > FS - Footswitch
> > RbnX - Ribbon Controller X-axis
> > RbnZ - Ribbon Controller Z-axis
> > Knob1~8 - Assign group knobs 1 ~ 8
> > SCENE - Scene Control controller
> > Between the Control Assign function (system) knob
> > assignments and Control Matrix (voice) knob assignments,
> > you can configure a monster knob control system where
> > each knob simultaneously controls either the same Control
> > Change parameter for the internal tone generator as for
> > an external tone generator, or different parameters for the
> > internal and external tone generator.
> > For more information about each parameter, see the separate Data List
> book.
> > For
> > information about the procedure for assigning controllers, see page 95.
> >
> >
> > Community email addresses:
> > Post message: AN1x-list@onelist.com
> > Subscribe: AN1x-list-subscribe@onelist.com
> > Unsubscribe: AN1x-list-unsubscribe@onelist.com
> > List owner: AN1x-list-owner@onelist.com
> >
> > Shortcut URL to this page:
> > http://www.onelist.com/community/AN1x-list
> >
>
> ------------------------------------------------------------------------
> Make music with anyone, anywhere, through FREE Internet
> recording studio software. FREE software download!
> http://click.egroups.com/1/3729/7/_/663009/_/957568032/
> ------------------------------------------------------------------------
>
> Community email addresses:
> Post message: AN1x-list@onelist.com
> Subscribe: AN1x-list-subscribe@onelist.com
> Unsubscribe: AN1x-list-unsubscribe@onelist.com
> List owner: AN1x-list-owner@onelist.com
>
> Shortcut URL to this page:
> http://www.onelist.com/community/AN1x-list