<div dir="ltr"><div>You were correct! I used a square wave, and I could immediately hear a normal chorus effect. I checked the scope, and I could see left and right movement.</div><div><br></div><div>I am curious to learn more - is this because the BBD circuit works on a limited frequency range, and a low frequency sine is outside of that range, but the harmonics in a square wave are within the range? This would explain some of the unique character that people say a BBD has.</div><div><br></div><div>Thank you so much!</div><div><br></div><div>I am going to swap the rate trimpot for a panel mounted pot, and then this thing is ready to use :)</div><div><br></div><div>Best regards,</div><div><br></div><div><div dir="ltr" class="gmail_signature" data-smartmail="gmail_signature"><div dir="ltr"><div dir="ltr"><font face="verdana, sans-serif" color="#444444"><b>Jacob Watters</b></font><div><font face="verdana, sans-serif" color="#444444"><a href="http://jacobwatters.com/" target="_blank">JacobWatters.com</a></font></div><div><br></div></div></div></div></div><br></div><br><div class="gmail_quote gmail_quote_container"><div dir="ltr" class="gmail_attr">On Sat, Feb 15, 2025 at 4:50 PM Richie Burnett <<a href="mailto:rburnett@richieburnett.co.uk">rburnett@richieburnett.co.uk</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">Try testing it with a sawtooth or square waveform.  With just a sinewave you <br>
can only really get amplitude modulation, especially if the test tone is <br>
quite a low pitch.  And that could sound like panning if you alternately get <br>
constructive interference on one side and destructive on the other side of <br>
the stereo image.  With a bright saw or squarewave at a decent pitch you <br>
should be able to hear some periodic detuning or at least some "phasing" <br>
between the dry and the chorused waveform edges.<br>
<br>
-Richie,<br>
<br>
<br>
<br>
-----Original Message----- <br>
From: Jacob Watters via Synth-diy<br>
Sent: Saturday, February 15, 2025 9:35 PM<br>
To: Richie Burnett<br>
Cc: SDIY<br>
Subject: Re: [sdiy] MN3007 Chorus Acting Weird<br>
<br>
<br>
I am testing it with a sine wave from a signal generator. When I look at a <br>
scope, I only see vertical movement. When I listen with my ears, I only hear <br>
panning.<br>
<br>
I found this photo of the service manual. It's difficult to read the exact <br>
values, but maybe someone familiar with the IC will be able to tell how it <br>
should be functioning. The BBD part is in the rectangle at the bottom with <br>
the "DC 1/2" label.<br>
<br>
<a href="https://rvb-img.reverb.com/image/upload/s--wzg-Dhdj--/f_auto,t_supersize/v1669410662/zuo0v17w68dkc6c0n99s.jpg" rel="noreferrer" target="_blank">https://rvb-img.reverb.com/image/upload/s--wzg-Dhdj--/f_auto,t_supersize/v1669410662/zuo0v17w68dkc6c0n99s.jpg</a><br>
<br>
Jacob Watters<br>
JacobWatters.com<br>
<br>
<br>
<br>
On Sat, Feb 15, 2025 at 4:28 PM Richie Burnett <br>
<<a href="mailto:rburnett@richieburnett.co.uk" target="_blank">rburnett@richieburnett.co.uk</a>> wrote:<br>
What input signal are you testing it with?<br>
<br>
-Richie,<br>
<br>
<br>
-----Original Message----- <br>
From: Jacob Watters via Synth-diy<br>
Sent: Saturday, February 15, 2025 9:17 PM<br>
To: SDIY<br>
Subject: [sdiy] MN3007 Chorus Acting Weird<br>
<br>
<br>
I am repairing a Yamaha KM602 mixer, which has a builtin MN3007 circuit. The<br>
chorus circuit behaves a bit odd. Instead of being a modulated delay that<br>
causes a pitch shift, it seems to behave like an auto-pan circuit. The sound<br>
level increases on one side, while decreasing on the other, and alternates<br>
back and forth. It is labelled as CHORUS on the front panel, so that is not<br>
the behavior that I expected.<br>
<br>
Is this normal, or is something wrong with the circuit?<br>
<br>
I tried finding a pdf of the service manual online, but I was unsuccessful.<br>
Does anyone have the service manual and can provide some input as to how the<br>
circuit should work?<br>
<br>
<br>
Thanks for your help!<br>
<br>
Best regards,<br>
<br>
Jacob Watters<br>
JacobWatters.com<br>
<br>
<br>
<br>
<br>
<br>
________________________________________________________<br>
This is the Synth-diy mailing list<br>
Submit email to: <a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
View archive at: <a href="https://synth-diy.org/pipermail/synth-diy/" rel="noreferrer" target="_blank">https://synth-diy.org/pipermail/synth-diy/</a><br>
Check your settings at: <a href="https://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">https://synth-diy.org/mailman/listinfo/synth-diy</a><br>
Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a><br>
<br>
<br>
-- <br>
This email has been checked for viruses by AVG antivirus software.<br>
<a href="http://www.avg.com" rel="noreferrer" target="_blank">www.avg.com</a><br>
<br>
<br>
<br>
<br>
<br>
<br>
________________________________________________________<br>
This is the Synth-diy mailing list<br>
Submit email to: <a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
View archive at: <a href="https://synth-diy.org/pipermail/synth-diy/" rel="noreferrer" target="_blank">https://synth-diy.org/pipermail/synth-diy/</a><br>
Check your settings at: <a href="https://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">https://synth-diy.org/mailman/listinfo/synth-diy</a><br>
Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a> <br>
<br>
</blockquote></div>