<div dir="ltr"><div dir="auto">In the absence of the datasheet, I'd consider trying a "better" op amp than the TL072, maybe an LT1013 or OPA2134, if I had them on hand (I personally do :) ).  Obviously the datasheet to get the actual details would be preferable....</div></div><div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sat, Jan 4, 2025 at 9:31 AM Florian Anwander <<a href="mailto:fanwander@mnet-online.de" target="_blank">fanwander@mnet-online.de</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><u></u>

  

    
  
  <div>
    Hello,<br>
    <br>
    I built a replacement for the SSK board in a Yamaha CS15,
    essentially using Old Crow's approach. My schematic is here:<br>
    <a href="https://florian-anwander.de/yamaha_cs15/CS15_SSK_FA__Nano_2_sch.png" target="_blank">https://florian-anwander.de/yamaha_cs15/CS15_SSK_FA__Nano_2_sch.png</a><br>
    The original schematic is here:<br>
<a href="https://florian-anwander.de/yamaha_cs15/Yamaha_CS-15_Servicemanual.pdf" target="_blank">https://florian-anwander.de/yamaha_cs15/Yamaha_CS-15_Servicemanual.pdf</a><br>
    <br>
    Everything works perfectly. Only after switching on, VCO2 plays in
    an extremely wide range, while VCO1 only plays over one octave
    across the entire keyboard. I can "cure" this by briefly
    interrupting the CV connection to VCO1.<br>
    <br>
    The difference between the two VCOs is that the TA7505M OpAmp, which
    provides the buffering for the portamento circuit, is connected
    directly to the IG00153 of VCO1; while for VCO2 there is an
    additional OpAmp stage before the IG00153 that provides the detune
    voltage. In my circuit I use a TL072 instead of the Toshiba TA7505M.<br>
    <br>
    Now I am looking for the datasheet of the TA7505M to find out what
    could cause the problem. There doesn't seem to be the datasheet on
    the web.<br>
    <br>
    Do any of you have a Toshiba Databook from the late 70s? Or does
    anyone have an idea how I could solve the problem in a simple way
    without having to make a new board (it is clear that I could also
    put a buffer in front of the IG00153).<br>
    <br>
    <br>
    Best regards</div><div><br>
    Florian<br>
    <pre cols="72" style="font-family:monospace">-- 
<a href="http://www.florian-anwander.de/" style="font-family:monospace" target="_blank">http://www.florian-anwander.de/</a></pre>
  </div>

________________________________________________________<br>
This is the Synth-diy mailing list<br>
Submit email to: <a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
View archive at: <a href="https://synth-diy.org/pipermail/synth-diy/" rel="noreferrer" target="_blank">https://synth-diy.org/pipermail/synth-diy/</a><br>
Check your settings at: <a href="https://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">https://synth-diy.org/mailman/listinfo/synth-diy</a><br>
Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a><br>
</blockquote></div></div>