<div dir="ltr">I recently repaired one that had a note that was stuck on. It turned out to be the leg of a resistor that broke off. Replacing that fixed the issue. It was difficult to see that the leg was broken until I applied heat to the solder joint and the leg moved around freely.<div><br></div><div>Maybe try closely inspecting, and maybe even reflowing the solder, for all components in the suspect areas.</div><div><br clear="all"><div><div dir="ltr" class="gmail_signature" data-smartmail="gmail_signature"><div dir="ltr"><div dir="ltr"><font face="verdana, sans-serif" color="#444444"><b>Jacob Watters</b></font><div><font face="verdana, sans-serif" color="#444444"><a href="http://jacobwatters.com/" target="_blank">JacobWatters.com</a></font></div></div></div></div></div><br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sun, Aug 4, 2024 at 3:01 PM Ben Walker <ben@audio.computer> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div class="msg1127523529425631881"><u></u><div><div>I’m fixing up an Arp Quartet that I got from eBay in a pretty bad condition. I’ve replaced a bunch of chips that were fried, repaired a broken ground trace on the filter board, and now it’s making some good noises. But there’s still something not right, and I can’t get my head around how it’s supposed to work from the <a href="https://www.polynominal.com/siel-orchestra/ARP%20Quartet%20Service%20Manual.pdf" target="_blank">schematic</a>.<br></div><div><br></div><div>- The brass sound works, but the attack is always short and the decay always (very) long<br></div><div>- The piano sound works<br></div><div>- The organ sound doesn’t work (no output)<br></div><div>- The string sound only works when “percussion” is engaged.<br></div><div><br></div><div>There’s obviously something wrong with the ADSR circuit. There are a couple of parts of that circuit (Board B, pp. 3-4 of the schematic) that are switched in and out by a 4016 quad switch, which explains why some sounds work (brass, strings + percussion and piano all enable the same bit of circuitry).<br></div><div><br></div><div>The KYBD GATE signal that is sent to the keyboard bus bar sits around +5V for the working sounds, and close to 0V for the others. So there’s no voltage hitting the input pin of the TDA1008, and therefore no output.<br></div><div><br></div><div>The ADSR signal just sits at +6V no matter what the setting or whether a key is pressed, which might explain the lack of working attack/decay</div><div><br></div><div>Does anyone have experience with the Quartet, or is anyone able to interpret the schematic and take a guess at which part is not doing its job?<br></div><div><br></div><div>Thanks,<br></div><div><br></div><div>Ben</div></div>________________________________________________________<br>
This is the Synth-diy mailing list<br>
Submit email to: <a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
View archive at: <a href="https://synth-diy.org/pipermail/synth-diy/" rel="noreferrer" target="_blank">https://synth-diy.org/pipermail/synth-diy/</a><br>
Check your settings at: <a href="https://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">https://synth-diy.org/mailman/listinfo/synth-diy</a><br>
Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a><br>
</div></blockquote></div>