<div dir="auto">Thanks again for the help. I started removing parts from around the key contact, and discovered a diode that was split in half. I replaced it, and now it works again.</div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, May 14, 2024, 9:12 a.m. Jacob Watters <<a href="mailto:jacobwatters@gmail.com">jacobwatters@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr">Thank you for the advice. I will test those things out tonight.<div><br></div><div>Best regards,<br><div><br clear="all"><div><div dir="ltr" class="gmail_signature" data-smartmail="gmail_signature"><div dir="ltr"><div dir="ltr"><font face="verdana, sans-serif" color="#444444"><b>Jacob Watters</b></font><div><font face="verdana, sans-serif" color="#444444"><a href="http://jacobwatters.com/" target="_blank" rel="noreferrer">JacobWatters.com</a></font></div></div></div></div></div><br></div></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Mon, May 13, 2024 at 11:31 PM Nathan Trites <<a href="mailto:nathan@idmclassics.net" target="_blank" rel="noreferrer">nathan@idmclassics.net</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="ltr">Hi Jacob,<div><br></div><div>The String and Brass settings likely use a different mix of octaves than the other two, which is why you lose the sound when going to those modes. The TDA clock divider chips in here have a VCA input to control the level of each output. Find the key that you're having the issue with and check the resistor/diode/caps going from the key's switch to see if the signal is stuck high. There's a good change that's happened, so you'll want to check out those components. </div><div><br>If it isn't high, it is important to keep in mind that when those clock divider chips begin to fail, certain notes can become stuck open, and get that slight volume change with the key. You'll want to make sure the PSU is running at expected voltages too - if the power rails aren't where they're supposed to be, you can start seeing similar issues.</div><div><br></div><div>Best,</div><div><br></div><div>Nathan</div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Mon, May 13, 2024 at 9:23 PM Jacob Watters via Synth-diy <<a href="mailto:synth-diy@synth-diy.org" target="_blank" rel="noreferrer">synth-diy@synth-diy.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="ltr"><div>I have an Arp Quartet that is making a constant sound of the B note near the middle of the keyboard.</div><div><br></div><div>It only makes the sound when Strings or Brass are turned on, and does not do it for Organ or Piano.</div><div><br></div><div>Also, the tone stops when the Percussion in the String section is turned up.</div><div><br></div><div>The key contact is not stuck to the power rail - so the key is not physically stuck in the ON position. Also, I can hear a very slight volume change in the sound when I press the same B key on the keybed. I think that this indicates that the envelope is being triggered properly.</div><div><br></div><div>I tried swapping the B divider chip with the one next to it, and the noise continued on the B. Removing the chip entirely stops the noise, but then I have no B notes.</div><div><br></div><div>The service manual is not the easiest to read. I think that I should be looking for either a short on the board with the keybed and dividers, or something on the F Board where only the strings and brass are filtered.</div><div><br></div><div>Does anyone have experience with this string machine? Can you maybe point me in the direction of what to check?</div><div><br></div><div><br></div><div>Thanks for the help.</div><div><br></div><div>Best regards,</div><br clear="all"><div><div dir="ltr" class="gmail_signature"><div dir="ltr"><div dir="ltr"><font face="verdana, sans-serif" color="#444444"><b>Jacob Watters</b></font><div><font face="verdana, sans-serif" color="#444444"><a href="http://jacobwatters.com/" target="_blank" rel="noreferrer">JacobWatters.com</a></font></div></div></div></div></div></div>
________________________________________________________<br>
This is the Synth-diy mailing list<br>
Submit email to: <a href="mailto:Synth-diy@synth-diy.org" target="_blank" rel="noreferrer">Synth-diy@synth-diy.org</a><br>
View archive at: <a href="https://synth-diy.org/pipermail/synth-diy/" rel="noreferrer noreferrer" target="_blank">https://synth-diy.org/pipermail/synth-diy/</a><br>
Check your settings at: <a href="https://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer noreferrer" target="_blank">https://synth-diy.org/mailman/listinfo/synth-diy</a><br>
Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank" rel="noreferrer">marketplace@synth-diy.org</a><br>
</blockquote></div>
</blockquote></div>
</blockquote></div>