<div dir="ltr"><div dir="ltr"><br></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">Am Mi., 6. März 2024 um 15:05 Uhr schrieb René Schmitz <<a href="mailto:synth@schmitzbits.de" target="_blank">synth@schmitzbits.de</a>>:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">Am 06.03.2024 um 00:36 schrieb hannes.janetzek--- via Synth-diy:<br>
> Hello - now that I have your attention I would like to bring up the <br>
> sad topic of the numerous synthesizers covering in 80s home-organs <br>
> that are daily thrown in the trash by their inheritors.<br>
> Ok maybe this is a specific southern Germany problem where it appears <br>
> every second home had a Hohner organ which outlived their role as <br>
> status symbol by now.. In the US these model were sold as Wurlitzer <br>
> Omni 3000-6500 - not sure if these are regularly in classified for <br>
> pickup as well.<br>
><br>
> My interest in these devices is mainly in their MEG sound-generator <br>
> for which I'm currently writing an interface library. As this starts <br>
> to work out nicely I wanted to throw in the filter boards and was very <br>
> surprised to see that all the VCAs and most of the mixing is powered <br>
> with ground to 12V.<br>
> Has anyone an idea what could be the reasoning or advantage of this <br>
> approach? (I'm very much a beginner on the analog electronics side)<br>
> The schematic is on page 35 and all boards I've seen use the BA6110 <br>
> version:<br>
> <a href="https://www.synthxl.com/wp-content/uploads/2020/08/Hohner-Symphonie-D98-Service-Manual.pdf" rel="noreferrer" target="_blank">https://www.synthxl.com/wp-content/uploads/2020/08/Hohner-Symphonie-D98-Service-Manual.pdf</a><br>
> Page 24-29 for the sound-generator - if you are curious.<br>
<br>
The reason is that the Iabc (the control current) is created with a <br>
resistor from a voltage referenced to GND.<br>
<br>
The OTAs sinks this current into the negative supply terminal.<br>
<br></blockquote><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">If you'd run them from +-12V then you need extra circuitry to translate <br>
the voltage.<br>
<br></blockquote><div> </div><div><div>Oh, yes! I recall scratching my head where the control current goes while trying to build the Ambika SMR filter with spare BA6110s.</div><div> </div></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">
(If you want to read a bit more on OTAs there is an article at my <br>
homepage, link below.)<br>
<br></blockquote><div> </div><div>yup, I found your collection while working on this filter. It will probably take a few more attempts for me to really grasp how these are working. </div><div> </div><div>Thanks everyone for the hints! The D98 filter-boards are probably good enough as-is for the first iteration of my Hohner polysynth. Figuring out how to properly calibrate the sound-generator DACs and timing for the integrators should be the next task before polishing the low end.</div><div><br></div><div>Regards</div><div>Hannes</div><div><br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">
<br>
Best,<br>
<br>
  René<br>
<br>
<br>
--<br>
<a href="mailto:synth@schmitzbits.de" target="_blank">synth@schmitzbits.de</a><br>
<a href="http://schmitzbits.de" rel="noreferrer" target="_blank">http://schmitzbits.de</a><br>
<br>
________________________________________________________<br>
This is the Synth-diy mailing list<br>
Submit email to: <a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
View archive at: <a href="https://synth-diy.org/pipermail/synth-diy/" rel="noreferrer" target="_blank">https://synth-diy.org/pipermail/synth-diy/</a><br>
Check your settings at: <a href="https://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">https://synth-diy.org/mailman/listinfo/synth-diy</a><br>
Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a><br>
</blockquote></div></div>