<div dir="ltr"><div>Interesting, thanks, but I can't see similar circuitry here.</div><div>The rev2 P5 is problematic in that each oscillator & filter has a number of opamp, CMOS switch and resistor inputs that can cause wild differences between voices ( that fabled "analog warmth" that some people think makes the rev2 superior to the rev3, but for service purposes is a pain in the balls).</div><div>Will attempt to swap out all oscillator chips and monitor all CMOS and opamps to see if anything is happening there.</div><div><br></div><div>~G<br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, May 2, 2023 at 3:20 PM Luís Marka via Synth-diy <<a href="mailto:synth-diy@synth-diy.org">synth-diy@synth-diy.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">Not sure if it helps since the electronics are different, but I had an <br>
issue with autotune in 2 voices on my Memorymoog clone. Turns out the <br>
Glide time trimpots for those voices was adjusted too high, and the CV <br>
injected into the VCOs was showing a slope when switching between the 0 <br>
/ 5 / 10V CV during the autotune routine, messing up the frequency <br>
counter and making autotune impossible. Readjusting the trimpot solved <br>
the problem (in the Memorymoog, each glide trimpot affects 2 voices). <br>
Maybe you could investigate how that particular voice reacts to <br>
frequency CV during autotune?<br>
<br>
Cheers!<br>
<br>
On 2023-05-02 2:11 p.m., g m montalbano via Synth-diy wrote:<br>
> I've been working on these for twenty years, and thought I'd seen <br>
> pretty much everything that could go wrong with them.<br>
> Now, I have one that works perfectly except for the fact that it will <br>
> not go through the tune procedure, either at powerup or when the Tune <br>
> button is pressed.<br>
><br>
> The confusing part is that the fault has been narrowed down to the <br>
> voice board: if I swap in a working voice board, the unit functions <br>
> correctly; if I install this voice board in another unit, the problem <br>
> follows.<br>
><br>
> As far as I can see, the ONLY parts on the voice board that relate to <br>
> tuning are the two 4051 multiplexers (U423 and U428) and the LM311 <br>
> comparator (and its associated resistors & caps). All of these <br>
> components have been replaced; traces and resistors have been checked <br>
> &  measured. All traces to the 60 pin connector between the CPU and <br>
> Voice boards are good, as is the 60 pin cable.<br>
> EVERYTHING is there, and everything works correctly except for Tune.<br>
><br>
> I've been hitting my head against this for a couple of weeks, and <br>
> would appreciate any suggestions as to where to look.<br>
><br>
> Thanks.<br>
> ~GMM<br>
><br>
> _______________________________________________<br>
> Synth-diy mailing list<br>
> <a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
> <a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
> Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a><br>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a><br>
</blockquote></div>