<p dir="ltr" style="margin-top:0; margin-bottom:0;">That cheap device is not bad just because it lack optocoupler but mostly because is unreliable and eats MIDI messages by design. It is capable of sending only max 4 byte messages, so forget about sysex.</p>
<br>
<p dir="ltr" style="margin-top:0; margin-bottom:0;">Roman </p><br><br>---- Użytkownik ShedSynth via Synth-diy napisał ----<br><br><div class=WordSection1><p class=MsoNormal><span style='mso-fareast-language:EN-US'>Re the video’s complaint that only MIDI IN is opto-isolated: I think I’m right that this is correct implementation (please contradict if not).<o:p></o:p></span></p><p class=MsoNormal><span style='mso-fareast-language:EN-US'>The MIDI OUT on any device is actively driven from the device’s own power, and whatever MIDI IN you plug that into will/should be opto-isolated so no ground loop or smoke.<o:p></o:p></span></p><p class=MsoNormal><span style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=MsoNormal><span style='mso-fareast-language:EN-US'>But the video is probably right about the £5 USB/MIDI interfaces not isolating MIDI IN.<o:p></o:p></span></p><p class=MsoNormal><span style='mso-fareast-language:EN-US'>Does anybody know any cheap USB/MIDI cables which do isolate?<o:p></o:p></span></p><p class=MsoNormal><span style='mso-fareast-language:EN-US'><o:p> </o:p></span></p><div style='border:none;border-top:solid #E1E1E1 1.0pt;padding:3.0pt 0cm 0cm 0cm'><p class=MsoNormal><b><span lang=EN-US>From:</span></b><span lang=EN-US> Synth-diy <<a href="mailto:synth-diy-bounces@synth-diy.org">synth-diy-bounces@synth-diy.org</a>> <b>On Behalf Of </b>Nathan Trites<br><b>Sent:</b> 13 January 2023 16:26<br><b>To:</b> David Messenger <<a href="mailto:mssngr1@pacifier.com">mssngr1@pacifier.com</a>><br><b>Cc:</b> <a href="mailto:synth-diy@synth-diy.org">synth-diy@synth-diy.org</a><br><b>Subject:</b> Re: [sdiy] M-Audio Midisport Uno Wire to pin ?<o:p></o:p></span></p></div><p class=MsoNormal><o:p> </o:p></p><div><p class=MsoNormal>If you havent sorted this out yet - here is a youtube video where you can see how it's wired: <a href="https://youtu.be/Xv5-5CUNFvI?t=75">https://youtu.be/Xv5-5CUNFvI?t=75</a><o:p></o:p></p><div><p class=MsoNormal><o:p> </o:p></p></div><div><p class=MsoNormal>Nathan<o:p></o:p></p></div></div><p class=MsoNormal><o:p> </o:p></p><div><div><p class=MsoNormal>On Sat, Jan 7, 2023 at 5:14 PM David Messenger <<a href="mailto:mssngr1@pacifier.com">mssngr1@pacifier.com</a>> wrote:<o:p></o:p></p></div><blockquote style='border:none;border-left:solid #CCCCCC 1.0pt;padding:0cm 0cm 0cm 6.0pt;margin-left:4.8pt;margin-right:0cm'><p class=MsoNormal>I have to rewire the in/out DINs on a Midisport Uno that lost it's midi <br>plugs. There is one wire that has red-black-yellow and a bare ground, <br>and then the other cable has just red and white. Anyone know which pins <br>each of these wires should be reattached to? TY D.<br><br><br>-- <br>This email has been checked for viruses by AVG antivirus software.<br><a href="http://www.avg.com" target="_blank">www.avg.com</a><br>_______________________________________________<br>Synth-diy mailing list<br><a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br><a href="http://synth-diy.org/mailman/listinfo/synth-diy" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a><o:p></o:p></p></blockquote></div></div>