<html><head><meta http-equiv="content-type" content="text/html; charset=utf-8"></head><body dir="auto">Always include a series resistor in series with the Iabc pins. You never need more than 2mA there (abs max). Size the resistor so a short to the positive supply will not draw more than 1mA. (Voltage is between V+ and V-). Then you can’t fry the OTA unless you short something directly to the Iabc pin. And you can measure the Iabc current by the voltage drop across the resistor as someone mentioned earlier.<div>Harry.<br><div><br><div dir="ltr">Sent from my iPhone</div><div dir="ltr"><br><blockquote type="cite">On Nov 20, 2022, at 3:30 PM, Roman <modular@go2.pl> wrote:<br><br></blockquote></div><blockquote type="cite"><div dir="ltr"><p dir="ltr" style="margin-top:0; margin-bottom:0;">I don't have any schematics at hand so it's just basic guideline. There is something going into Iabc pin of LM13600. If it's a resistor, then simply measure voltage across that resistor and use Ohm law to calculate current. If it's supplied directly from PNP transistor's collector (most typical use) find a resistor that is going to emiter of that transistor, and do as previously described. In any scenario you may just desolder or cut the trace to Iabc pin and measure it with ampmeter. Or better yet, put a resistor there if there wasn't any, it can only help. 4k7 for starters. It will make future troubleshoting easier, not to mention it also prevents LM13600 from accidental smoking.</p>
<br>
<p dir="ltr" style="margin-top:0; margin-bottom:0;">Roman </p><br><br>---- Użytkownik JoeF napisał ----<br><br><div dir="auto">Roman and Pete, TY. Roman, I want to move to the next level. Could you pont the way to how to determine current flow. I know how to check voltage and perform audio traces but I don't know how to determine current. If it's not too difficult, could you explain or point to a site that would explain. Tx again. JoeF.<br><br></div>
<div dir="auto"><!-- tmjah_g_1299s -->Get <!-- tmjah_g_1299e --><a href="http://www.typeapp.com/r"><!-- tmjah_g_1299s -->TypeApp for Android<!-- tmjah_g_1299e --></a><!-- tmjah_g_1299s --> <!-- tmjah_g_1299e --></div>
<div class="gmail_quote">On Nov 20, 2022, at 2:44 AM, Roman <<a href="mailto:modular@go2.pl" target="_blank">modular@go2.pl</a>> wrote:<blockquote class="gmail_quote" style="margin: 0pt 0pt 0pt 0.8ex; border-left: 1px solid rgb(204, 204, 204); padding-left: 1ex;">
<p dir="ltr" style="margin-top:0; margin-bottom:0;">Measure the Iabc current going to LM13600 to check if they are open at all. Measure voltages at OTAs and opamps outputs to see if they are not terribly close to one of supply rails. </p>
<br>
<p dir="ltr" style="margin-top:0; margin-bottom:0;">Roman </p>
<br>
<br>---- Użytkownik JoeF napisał ----
<br>
<br>
<div dir="auto">
Hello all, not sure if this is the right place to ask for guidance but, I'll try. I have put together an Echo Rockit I got as a kit. And, of course I need to troubleshoot.
<br>
</div>
<div dir="auto">
This is an oscillator and external input into a VCF into a PT2399 delay. I am getting no sound at the output and I believe it is because the VCF is not functioning. I have audio traced a signal to the VCF from the input and the internal oscillator. And, I have jumped the signals around the VCF straight to the delay and then I get output and have verified the delay is operating as expected. I have correct power to all IC power pins. The transistors are getting power on their source
<a href="http://pins.The">pins.The</a> IC in the VCF is an
<a href="tel:13600">13600</a>D which I have spares of and have swapped to no avail. I have re-soldered the components in the VCF circuit. I don't have extras of the MPF102 transistors and am questioning whether I burned them up when I soldered them in? What do you think?
<br>
</div>
<div dir="auto">
What's next? Thanks for any advice in advance. JoeF.
<br>
<br>
</div>
<div dir="auto">
<!-- tmjah_g_1299s -->Get
<!-- tmjah_g_1299e -->
<a href="http://www.typeapp.com/r">
<!-- tmjah_g_1299s -->TypeApp for Android
<!-- tmjah_g_1299e --></a>
<!-- tmjah_g_1299s -->
<!-- tmjah_g_1299e -->
</div></blockquote></div><span>_______________________________________________</span><br><span>Synth-diy mailing list</span><br><span>Synth-diy@synth-diy.org</span><br><span>http://synth-diy.org/mailman/listinfo/synth-diy</span><br><span>Selling or trading? Use marketplace@synth-diy.org</span><br></div></blockquote></div></div></body></html>