<div dir="ltr"><div dir="ltr">Thanks to everyone for the helpful suggestions and thoughts! The remarks made about the original intention (and current limits) of the USB standard made me rethink the whole plan once more. I did not feel comfortable pushing so much current through relatively thin USB cables, and discovered a better way to inject the required power. I've bought an extension cable for a sata(male)-to-sata(female) connection. I've placed it in-between the SSD drive and the sata-to-USB adapter, and cut the +5V and one of the 2 ground wires on it. This allows me to inject power right before the SSD. The sata-to-USB converter still takes its power from Pi's USB bus, but the SSD no longer does. Currently it runs on my lab supply, allowing me to measure the current requirement of the final NAS with all drives attached, and size the final PSU accordingly.</div><div dir="ltr"><br></div><div>Rutger</div><div><br></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">Op di 8 nov. 2022 om 22:38 schreef <a href="mailto:dh@atoav.com">dh@atoav.com</a> <<a href="mailto:dh@atoav.com">dh@atoav.com</a>>:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">I am only going to comment on plan C as I did this before:<br>
<br>
You can get yourself a beefy enough 5V PSU¹ and directly power the Raspi <br>
(per USB or by soldering two wires to the right pads. Then you connect <br>
your externals in parallel to the beefy power supply using thick enough <br>
wire (one for GND one for 5V).<br>
<br>
Then for the USB data connection you connect anything, except for the 5V <br>
which comes already from the PSU directly. So: GND, Data+, Data- are <br>
connected, but no 5V.<br>
<br>
For this you can just cut an USB-cable, strip the isolation and cut the <br>
5V wire and frankenstein everything back together. Alternatively you can <br>
get USB-powerblockers that do this for you. Make sure GND (0V) is still <br>
connected tho: GND is mostly for the shielding to protect your precious <br>
Data from stray EMF interference.<br>
<br>
This way the current for the SSDs will be not running through the Raspi, <br>
but comes directly from the PSU and because the PSU-GND and the <br>
Raspi-GND is shared there should be no (harmful) voltage differential <br>
between the external 5V and Raspi 5V.<br>
<br>
Note that with isolated PSUs this should even work with multiple such <br>
supplies as long as their secondary GNDs are connected.<br>
<br>
<br>
Cheers,<br>
David/atoav<br>
<br>
---<br>
¹ If you get a PSU that has connectors that go to mains power, please <br>
don't do this yourself unless you _really_ know what you are doing (e.g. <br>
you have been trained to do this). Mains voltage can kill you even hours <br>
after you had the very painful experience. By being smart this can be <br>
avoided from the start.<br>
<br>
On 08/11/2022 19:28, Rutger Vlek wrote:<br>
> Plan C, that just came to mind, is that I might be able to find a beefy <br>
> USB PSU with multiple ports, that I can use to feed the Pi from, as well <br>
> as the drives via Y-cable. The Y-cable would then be combining the power <br>
> from Pi's USB output with the direct output of the same PSU. Would that <br>
> work?<br>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a><br>
</blockquote></div></div>