<div dir="auto">Hi Jean-Pierre,<div dir="auto"><br></div><div dir="auto">So nice to see another player piano fan here! I have been interested in mechanical musical instruments since early age and have some experience in arranging music for them, particularly for mechanical organs.</div><div dir="auto"><br></div><div dir="auto">Recently I bought a Steck pianola, which is still awaiting restoration.</div><div dir="auto"><br></div><div dir="auto">I've been thinking about your problem, and was curious to hear if you have considered an alternative route without the need for custom electronics. With a modern smartphone on a stand, it should be possible to capture a movie of the pianoroll while playing. With modern computer vision techniques (AI is my daytime job, though not computer vision specifically) it should be possible to recognize the holes in specific areas and convert the information MIDI. I did a quick calculation of the spatial resolution, and think that with a common framerate of 60 fps you have around 1mm accuracy between frames when the roll is at its max speed of 13 feet per minute. Additional accuracy might be possible when identifying the exact start/end of a hole in each frame.</div><div dir="auto"><br></div><div dir="auto">Rutger </div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">Op zo 13 nov. 2022 12:31 schreef Roman Sowa <<a href="mailto:modular@go2.pl">modular@go2.pl</a>>:<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">One thin heated wire in front of the holes would indeed be most elegant <br>
solution, but I'm also not sure if those wavelengths are in range of <br>
optotransistor sensing. And what is more important, such solution would <br>
not block ambient light in any way, so you could play it from the <br>
distance with a flashlight :)<br>
<br>
It's no problem for JLC to make 5mm wide long PCB filled with SMD IR <br>
LEDs, and IMHO it is cute. Maybe even 5mm will be too narrow to block <br>
ambient light, so maybe more like 10mm sounds like good choice. And on <br>
the back side you can put some art-deco graphics to match the aesthetics <br>
of entire instrument.<br>
<br>
Roman<br>
<br>
W dniu 2022-11-11 o 15:58, Jean-Pierre Desrochers pisze:<br>
<br>
(...)<br>
> I was thinking of something else that could work..<br>
><br>
> Heat is Infrared so.. Using a heating element wire over all the brass <br>
> bar holes<br>
> could be seen as a LEDS array but smaller in width (no PCB).<br>
> This wire just heated a little could be glued in a plexiglass <br>
> transparent Bar<br>
> placed over the brass reading bar.??<br>
> Or use some kind of diffused incandescent light all over the scrolling <br>
> paper<br>
> that has infrared specs close to 940nm.. ?<br>
><br>
> But I’m about sure heating wire spectral wavelength would be far from <br>
> my needed 940nm..<br>
><br>
> Hmmm…<br>
><br>
><br>
<br>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank" rel="noreferrer">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank" rel="noreferrer">marketplace@synth-diy.org</a><br>
</blockquote></div>