<div dir="ltr"><div><a href="https://oshpark.com/shared_projects/xdfK07Ms">https://oshpark.com/shared_projects/xdfK07Ms</a></div><div><br></div><div>There's this shared project up on OSHPark.  I haven't ordered some yet but been meaning to get around to it.<br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sun, Aug 7, 2022 at 7:38 PM BrightBoy via Synth-diy <<a href="mailto:synth-diy@synth-diy.org">synth-diy@synth-diy.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><p style="font-family:Arial,Helvetica,sans-serif;margin:0.1rem 0px;line-height:1.1">It still boggles the mind the spacing on a 2032 battery with integrated legs</p>
<p style="font-family:Arial,Helvetica,sans-serif;margin:0.1rem 0px;line-height:1.1">is different from leg spacing on a 2032 battery holder.</p>
<p style="font-family:Arial,Helvetica,sans-serif;margin:0.1rem 0px;line-height:1.1"> </p>
<p style="font-family:Arial,Helvetica,sans-serif;margin:0.1rem 0px;line-height:1.1">To my knowledge and that no one has made a retrofit holder to match.</p>
<p style="font-family:Arial,Helvetica,sans-serif;margin:0.1rem 0px;line-height:1.1"> </p>
<p style="font-family:Arial,Helvetica,sans-serif;margin:0.1rem 0px;line-height:1.1">Someone take my 25 year old idea and run with it. Please!!!!</p>
<p style="font-family:Arial,Helvetica,sans-serif;margin:0.1rem 0px;line-height:1.1"> </p>
<p style="font-family:Arial,Helvetica,sans-serif;margin:0.1rem 0px;line-height:1.1">Cheers,</p>
<p style="font-family:Arial,Helvetica,sans-serif;margin:0.1rem 0px;line-height:1.1"> </p>
<p style="font-family:Arial,Helvetica,sans-serif;margin:0.1rem 0px;line-height:1.1">Jeff</p>
<p style="font-family:Arial,Helvetica,sans-serif;margin:0.1rem 0px;line-height:1.1"> </p>
<u></u><u></u><u></u>
<div>-----Original Message-----<br>From: brianw <<a href="mailto:brianw@audiobanshee.com" target="_blank">brianw@audiobanshee.com</a>><br>Sent: Aug 7, 2022 5:12 PM<br>To: Jean-Pierre Desrochers <<a href="mailto:jpdesroc@oricom.ca" target="_blank">jpdesroc@oricom.ca</a>><br>Cc: <<a href="mailto:synth-diy@synth-diy.org" target="_blank">synth-diy@synth-diy.org</a>><br>Subject: Re: [sdiy] Oberheim Matrix 6 ---- 3.6v Lithium battery replacement.. or not ?<br>
<p style="font-family:Arial,Helvetica,sans-serif;margin:0.1rem 0px;line-height:1.1"> </p>
<p style="margin:0.1rem 0px;line-height:1">I recommend:</p>
<p style="margin:0.1rem 0px;line-height:1"> </p>
<p style="margin:0.1rem 0px;line-height:1">#1) leaving it alone until it fails. I've never seen a 2032 leak.</p>
<p style="margin:0.1rem 0px;line-height:1"> </p>
<p style="margin:0.1rem 0px;line-height:1">#2) replacing with an identical BR2032 with the correctly-spaced legs for this PCB, assuming that you have plenty of experience with soldering vintage gear without damaging things like the pads. The worst thing is starting with a working synth and ending up with one that doesn't work, due to mysterious soldering issues.</p>
<p style="margin:0.1rem 0px;line-height:1"> </p>
<p style="margin:0.1rem 0px;line-height:1">In particular, I recommend against modifying the Matrix 6 with either a battery holder or wire extensions. The single worst thing I've found when buying used synths is a battery flopping around and damaging other rare components because someone failed to replace the battery with the original configuration. These modifications are always worse than the original, or a replacement that's identical to the original.</p>
<p style="margin:0.1rem 0px;line-height:1"> </p>
<p style="margin:0.1rem 0px;line-height:1">Note that if you're finding BR2032 battery cells that don't fit the Matrix 6, then you need to keep looking. Go to a manufacturer site like Panasonic, and search their product category. Once you have confirmed the measurements of the pin spacings, look for an exact match in their catalog. From there, you'll have a specific product number to search for.</p>
<p style="margin:0.1rem 0px;line-height:1"> </p>
<p style="margin:0.1rem 0px;line-height:1">Case in point: I recently repaired an Ensoniq ESQ1. Searching the usual distributor sites, I couldn't quite find the right battery, or at least there didn't seem to be any guarantee about the pin spacings. After I looked in a battery manufacturer catalog and got an actual part number, it was really easy to find a distributor with parts in stock, cheap. This wasn't a 2032 battery, by the way, but the process of finding an appropriate part number works the same.</p>
<p style="margin:0.1rem 0px;line-height:1"> </p>
<p style="margin:0.1rem 0px;line-height:1">Brian Willoughby</p>
<p style="margin:0.1rem 0px;line-height:1"> </p>
<p style="margin:0.1rem 0px;line-height:1"> </p>
<p style="margin:0.1rem 0px;line-height:1">On Aug 7, 2022, at 9:07 AM, John Speth wrote:</p>
<p style="margin:0.1rem 0px;line-height:1">> Regarding soldering, I've faced that problem in the past. I've had good luck with preparing a battery by soldering red/black pigtails to the battery, wrapping it in heat shrink tubing, then soldering the pigtails to the board after snipping (no heat) the old battery out. Then figure out some way to anchor the battery (tie-wraps, etc) if necessary. It also makes it easier to replace the battery again 30 years later :)</p>
<p style="margin:0.1rem 0px;line-height:1">></p>
<p style="margin:0.1rem 0px;line-height:1">> I think the key when working on old fragile boards is to take every precaution to avoid heating the board due to soldering. The pigtails provide a measure of soldering heat isolation. Soldering the wires to the battery requires a hot iron and flux.</p>
<p style="margin:0.1rem 0px;line-height:1">></p>
<p style="margin:0.1rem 0px;line-height:1">> JJS</p>
<p style="margin:0.1rem 0px;line-height:1">></p>
<p style="margin:0.1rem 0px;line-height:1">> On 8/7/2022 7:33 AM, Jean-Pierre Desrochers wrote:</p>
<p style="margin:0.1rem 0px;line-height:1">>> Hi all,</p>
<p style="margin:0.1rem 0px;line-height:1">>> A friend of mine brought me a working Oberheim Matrix 6 keyboard</p>
<p style="margin:0.1rem 0px;line-height:1">>> that he was worried about the inner memory lithium battery (BR2032)</p>
<p style="margin:0.1rem 0px;line-height:1">>> being about to die.. and to replace it.</p>
<p style="margin:0.1rem 0px;line-height:1">>> Well after a quick check the battery was still in pretty good physical condition (no leakage)</p>
<p style="margin:0.1rem 0px;line-height:1">>></p>
<p style="margin:0.1rem 0px;line-height:1">>></p>
<p style="margin:0.1rem 0px;line-height:1">>> and was showing a strong 3.23v on its terminal (AC unconnected)</p>
<p style="margin:0.1rem 0px;line-height:1">>> So.. In this situation I’m wondering if this lithium cell should be replaced or not.</p>
<p style="margin:0.1rem 0px;line-height:1">>> I know this keyboard is at least 30-40 years old and many of the coin</p>
<p style="margin:0.1rem 0px;line-height:1">>> batteries of these vintage keyboards need to be replaced, but..</p>
<p style="margin:0.1rem 0px;line-height:1">>> And on replacement I thought about soldering a coin battery socket</p>
<p style="margin:0.1rem 0px;line-height:1">>> on the PCB pads BUT the battery placement on the PCB</p>
<p style="margin:0.1rem 0px;line-height:1">>> is very close to some IC’s as shown on the picture and</p>
<p style="margin:0.1rem 0px;line-height:1">>> would need the socket to be raised a little to avoid these IC’s.. I don’t like that.</p>
<p style="margin:0.1rem 0px;line-height:1">>> I could also buy a coin battery with PCB legs too like this one</p>
<p style="margin:0.1rem 0px;line-height:1">>> but again, replacement or not ?</p>
<p style="margin:0.1rem 0px;line-height:1">>></p>
<p style="margin:0.1rem 0px;line-height:1">>> I don’t know the year of manufacture of this Matrix but here are</p>
<p style="margin:0.1rem 0px;line-height:1">>> the serial number and BIOS number.</p>
<p style="margin:0.1rem 0px;line-height:1">>> SN: 7622661</p>
<p style="margin:0.1rem 0px;line-height:1">>> BIOS: M6R 2.13</p>
<p style="margin:0.1rem 0px;line-height:1">>></p>
<p style="margin:0.1rem 0px;line-height:1">>> Your opinions are very welcomed.</p>
<p style="margin:0.1rem 0px;line-height:1">>> Cheers !</p>
<p style="margin:0.1rem 0px;line-height:1">>> Jean-Pierre</p>
<p style="margin:0.1rem 0px;line-height:1"> </p>
<p style="margin:0.1rem 0px;line-height:1"> </p>
<p style="margin:0.1rem 0px;line-height:1">_______________________________________________</p>
<p style="margin:0.1rem 0px;line-height:1">Synth-diy mailing list</p>
<p style="margin:0.1rem 0px;line-height:1"><a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a></p>
<p style="margin:0.1rem 0px;line-height:1"><a href="http://synth-diy.org/mailman/listinfo/synth-diy" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a></p>
<p style="margin:0.1rem 0px;line-height:1">Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a></p>
</div>
<u></u>
<p style="font-family:Arial,Helvetica,sans-serif;margin:0.1rem 0px;line-height:1.1"> </p>_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a><br>
</blockquote></div>