<div dir="ltr">Oh nice.  Thank you!  I'd be interested if you want to message me off list or whatever.  Are they official?  The keyboard schematics on the Tauntek site have been helpful but I haven't made much progress after looking at it more today.  I turned all the oscillator trims fully down and I have the full keyboard working again except most of the keys drone like crazy.  I'm hoping I can find the sweet spot but I can't measure the oscillators' frequency with the keys in place and the frequency is meaningless without the keys in place.  <div><br></div><div>I've seen a service manual for the ASR10 but it's basically "if you have a problem here, this is the board swap you need to do".  No mention of where to set the trims.</div><div><br></div><div>It's a shame because I really like ensoniq gear but the lack of service info sucks so bad.</div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Fri, Jul 1, 2022 at 9:32 PM grant <a href="http://musictechnologiesgroup.com">musictechnologiesgroup.com</a> <<a href="mailto:grant@musictechnologiesgroup.com">grant@musictechnologiesgroup.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">I have the schematics for the KPC HC11 board that you speak of. It's 1MB <br>
so I'm not sure everyone wants it email blasted. I had a spare KPC board <br>
way back when that I re-purposed into something or other for a local <br>
museum. No idea what that was but I probably have the HC11 assembler <br>
source somewhere...<br>
<br>
GB<br>
<br>
<br>
------ Original Message ------<br>
From: "brianw" <<a href="mailto:brianw@audiobanshee.com" target="_blank">brianw@audiobanshee.com</a>><br>
To: "Peter Pearson" <<a href="mailto:electrocontinuo@gmail.com" target="_blank">electrocontinuo@gmail.com</a>><br>
Cc: "synth-diy mailing list" <<a href="mailto:synth-diy@synth-diy.org" target="_blank">synth-diy@synth-diy.org</a>><br>
Sent: 7/1/2022 4:32:19 PM<br>
Subject: Re: [sdiy] Ensoniq keyboard calibration advice?<br>
<br>
>Oh!<br>
><br>
>I didn't realize that the ASR-10 is a couple of years newer than the VFX. This is probably because I got my ASR-10R directly from Ensoniq when it was brand new (subsequently stolen from me) and then I got my VFX many years later, used. I had assumed that *all* of the Ensoniq PolyAT keyboards used the same KPC circuit board mounted under the keyboard, with socketed 68HC11 processor and EPROM (plus maybe a few more).<br>
><br>
>Are there any ASR-10 schematics around?<br>
><br>
>Brian<br>
><br>
><br>
>On Jul 1, 2022, at 3:25 PM, Peter Pearson <<a href="mailto:electrocontinuo@gmail.com" target="_blank">electrocontinuo@gmail.com</a>> wrote:<br>
>>  Hi Brian.  I know what you're talking about with the EPS keyboard.  The ASR10 keyboard I'm looking at is mostly surface mount and nothing is socketed.  The 2 keyboard PCBs have a ribbon cable between them.  I already cleaned and resoldered the connectors between the boards.  Feel you on the back sockets and oxidized pins though.  Very annoying when you come across that.<br>
>><br>
>>  On Fri, Jul 1, 2022 at 4:58 PM brianw <<a href="mailto:brianw@audiobanshee.com" target="_blank">brianw@audiobanshee.com</a>> wrote:<br>
>>>  I have no reason to doubt your statement, but...<br>
>>><br>
>>>  Considering that I purchased my EPS new in 1988, I'm not exactly disappointed that some oxidization (or whatever happens to old socketed chips) had to be broken free after three decades. I didn't think I was buying military-grade equipment, and even military-grade equipment requires frequent maintenance for continued reliability.<br>
>>><br>
>>>  At least it's not like the Apple /// ... where chips literally fell out of their sockets and the product stopped working.<br>
>>><br>
>>>  Brian<br>
>>><br>
>>><br>
>>>  On Jul 1, 2022, at 9:29 AM, Rainer Buchty <<a href="mailto:rainer@buchty.net" target="_blank">rainer@buchty.net</a>> wrote:<br>
>>>  > On Thu, 30 Jun 2022, brianw wrote:<br>
>>>  >> Have you tried gently removing the main chip and then plugging it in again?<br>
>>>  ><br>
>>>  > Definitely good advice on Ensoniq gear. They used quite some crappy DIL/DIP sockets.<br>
>>>  ><br>
>>>  > Rainer<br>
>>>  ><br>
>>><br>
>><br>
><br>
>_______________________________________________<br>
>Synth-diy mailing list<br>
><a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
><a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
>Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a></blockquote></div>