<div dir="ltr">I've tried two commercial versions of those pcb holders - but personally I find it's easier to rubber band the pcb to a foam sponge on a chunk of wood.<div><br></div><div>paul perry Melbourne Australia</div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Wed, May 18, 2022 at 9:12 PM Mikko Helin via Synth-diy <<a href="mailto:synth-diy@synth-diy.org">synth-diy@synth-diy.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">There were DIY pcb holder instructions on Nuts and Volts:<br>
<a href="https://www.nutsvolts.com/?/magazine/article/september2011_Collier" rel="noreferrer" target="_blank">https://www.nutsvolts.com/?/magazine/article/september2011_Collier</a><br>
<br>
On Tue, May 17, 2022 at 2:10 PM Tony Allgood via Synth-diy<br>
<<a href="mailto:synth-diy@synth-diy.org" target="_blank">synth-diy@synth-diy.org</a>> wrote:<br>
><br>
> I make boards with both surface mount and through hole. For me the<br>
> assembly time by hand is pretty much the same in each case.<br>
><br>
> Surface mount uses less solder and generally less waste. I generally<br>
> prefer to solder surface mount. However, for prototyping I still use<br>
> strip board with through hole parts.<br>
><br>
> Anyone who is soldering through hole components on large PCBs really<br>
> should be using an assembly jig. For example:<br>
><br>
> <a href="https://uk.farnell.com/ideal-tek/pcsa-1n/esd-safe-pcb-holder-280mm-x-220mm/dp/3605333" rel="noreferrer" target="_blank">https://uk.farnell.com/ideal-tek/pcsa-1n/esd-safe-pcb-holder-280mm-x-220mm/dp/3605333</a><br>
><br>
> It makes the whole job go a lot quicker.<br>
><br>
> BTW: The Fender Rumble amplifier that was referenced in the original<br>
> post has surface mount PCBs including the LM13700.<br>
><br>
> Tony<br>
><br>
> <a href="http://www.oakleysound.com" rel="noreferrer" target="_blank">www.oakleysound.com</a><br>
><br>
> _______________________________________________<br>
> Synth-diy mailing list<br>
> <a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
> <a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
> Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a><br>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a><br>
</blockquote></div>