<div dir="auto">Not sure what the footprint guidelines for this part are but I would arrange my footprint to have a few vias under the large pads and plan to apply hot air from below to flow solder paste on to all the pads. <div dir="auto">Gerry</div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Fri, 18 Feb 2022, 18:47 Roman, <<a href="mailto:modular@go2.pl">modular@go2.pl</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><p dir="ltr" style="margin-top:0;margin-bottom:0">Yes, it is doable with soldering iron. Sharp chisel or knife type, with flux gel and microscipe. No way of course to solder botom pads, so it will be poorly heatsinked. But I guess for a prototype you won't be driving it full power anyway.</p>
<p dir="ltr" style="margin-top:0;margin-bottom:0">You might also try solder paste and hot air, but IMHO that's more risky and difficult.</p>
<br>
<p dir="ltr" style="margin-top:0;margin-bottom:0">I'm not inUK so can't help you, although I'd gladly do it for free.</p>
<br>
<p dir="ltr" style="margin-top:0;margin-bottom:0">Roman </p><br><br>---- Użytkownik Mike Bryant napisał ----<br><br>
<div>
<p class="MsoNormal">Is it possible to assemble this product by hand ?<u></u><u></u></p>
<p class="MsoNormal"><u></u> <u></u></p>
<p class="MsoNormal"><a href="https://www.infineon.com/cms/en/product/power/class-d-audio-amplifier-ic/integrated-class-d-audio-amplifier-ics/ma5332ms/?redirId=160809" target="_blank" rel="noreferrer">https://www.infineon.com/cms/en/product/power/class-d-audio-amplifier-ic/integrated-class-d-audio-amplifier-ics/ma5332ms/?redirId=160809</a><u></u><u></u></p>
<p class="MsoNormal"><u></u> <u></u></p>
<p class="MsoNormal">I can get a PCB made at JLCPCB with all the support circuitry on it and leave plenty of space for this IC, but not sure if it’s possible to assemble this part afterwards.<u></u><u></u></p>
<p class="MsoNormal">It has a recommended stencil design in the datasheet which seems pretty tight for manual placement.<u></u><u></u></p>
<p class="MsoNormal"><u></u> <u></u></p>
<p class="MsoNormal">Alternatively anybody in the UK with whatever equipment is needed and willing to do it (paid for obviously) please email me.<u></u><u></u></p>
<p class="MsoNormal"><u></u> <u></u></p>
</div>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank" rel="noreferrer">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank" rel="noreferrer">marketplace@synth-diy.org</a><br>
</blockquote></div>