<div dir="ltr">These aren't elegant repair suggestions, but I hope you find them helpful.  My general start for Xpander repairs are:<div><br></div><div>If your Xpander is the Japanese version, it's probably got leaky corroded electrolytic capacitors on the voice board.  Swap them all out.</div><div><br></div><div>Replace all 4051s (especially U805) and chip select ICs.  Replace the LM311 tune comparator (U108)  Press down on all the other socketed ICs to make sure they're seated nice.</div><div><br></div><div>Replacing the polystyrene caps in the DAC (C805 and C806) has been useful in the past.</div><div><br></div><div>A list of factory ECOs for the Xpander is here and can also prove useful:</div><div><br></div><div><a href="http://www.electrongate.com/obfiles/Xpander/index.html">http://www.electrongate.com/obfiles/Xpander/index.html</a><br></div><div><br></div><div>Best of luck with it!</div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, Aug 10, 2021 at 6:03 PM Tom Wiltshire <<a href="mailto:tom@electricdruid.net">tom@electricdruid.net</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">Your email makes me realise that I don’t understand the Xpander schematics as well as I thought I did.<br>
<br>
On the page labelled “pg55” of the service manual (page 54 in my pdf) there’s a pair of 4051 switches which deal with general CVs for the voices. The first of which is the VCOF2 signal which presumably is the frequency modulation for VCO2. If that was bad, VCO2 would go out. But it seems to me to be a “per-voice” CV, so I can’t see how any single fault could take out all the voices at once.<br>
<br>
Clearly there are assumptions here about how the synth works and how the firmware treats the hardware when it’s doing the tuning routine, which is what I meant about not understanding this thing as well as I thought I did.<br>
<br>
Thoughts, please?<br>
<br>
Tom<br>
<br>
==================<br>
       Electric Druid<br>
Synth & Stompbox DIY<br>
==================<br>
<br>
<br>
<br>
> On 10 Aug 2021, at 19:37, gm via Synth-diy <<a href="mailto:synth-diy@synth-diy.org" target="_blank">synth-diy@synth-diy.org</a>> wrote:<br>
> <br>
> I have here an Xpander that will either pass or fail Tune, but will always have the VCO 1s in perfect tune & scale, while all six VCO 2s will be out of tune & out of scale.<br>
> <br>
> Did the usual replacement of all DAC components, and the ICs involved in the tuning routine;  no help.<br>
> <br>
> Am struggling to find what all six VCO 2s have in common that might be causing this;  any pointers would be greatly appreciated.<br>
> <br>
> ~GMM<br>
> _______________________________________________<br>
> Synth-diy mailing list<br>
> <a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
> <a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
> Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a><br>
<br>
<br>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a><br>
</blockquote></div>