<div dir="auto">Hi Neil,<div dir="auto"><br></div><div dir="auto">You might want to have a look at the Tilt EQ implementation done by Rob Hordijk for the Nord Modular G2 (a virtual modular).</div><div dir="auto"><br></div><div dir="auto">It inspired me when I made the River Marble eurorack module, which is basically two dual VC-tilt EQs. Just like the Hordijk implementation it's based on two all-pass filters per channel, but there was an issue with the mixture of these filters, causing the downward tilt to approximate the desired 3db/oct slope, but the upward tilt to behave less nicely. I solved that by using separate weigthing for upward and downward tilt. You can achieve that and the VC by using a ring modulator (I would suggest a 2164 based ringmod).</div><div dir="auto"><br></div><div dir="auto">Rutger</div><div dir="auto"><br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">Op zo 30 mei 2021 19:24 schreef Neil Harper via Synth-diy <<a href="mailto:synth-diy@synth-diy.org">synth-diy@synth-diy.org</a>>:<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">I recently breadboarded this tilt equalizer filter as found on EDN:<br>
<br>
<a href="https://www.edn.com/implement-an-audio-frequency-tilt-equalizer-filter/" rel="noreferrer noreferrer" target="_blank">https://www.edn.com/implement-an-audio-frequency-tilt-equalizer-filter/</a><br>
<br>
A similar (the same?) circuit is shown here:<br>
<a href="https://sound-au.com/articles/eq.htm#s10" rel="noreferrer noreferrer" target="_blank">https://sound-au.com/articles/eq.htm#s10</a><br>
<br>
It's pretty cool, low parts count and can sound interesting - i'm kinda<br>
digging it to eq an fx for sample.<br>
<br>
of course my next question was "how can I get this under voltage control"?<br>
<br>
here's what I plan to try, maybe you can steer me in the right direction.<br>
<br>
my first guess was to replace the potentiometer (P1) with two<br>
vactrols/LDRs, but I'm not sure how to basically 'crossfade' the two<br>
vactrols in opposite directions and I think the response curves of the<br>
vactrols with regard to voltage input (light) and resistance are far<br>
from linear.<br>
<br>
i've read that OTA's like the LM13700 (the monty python chip) can be<br>
used as voltage controlled resistors, but I've never seen them<br>
implemented as a pair replacing a potentiometer - so I don't know if<br>
that route is possible either.<br>
<br>
my last guess was wondering if an equivalent circuit could be made by<br>
combining a lowpassed and hipassed audio signal and then crossfading<br>
them. I can imagine it would somewhat similar, but I'm not sure if you<br>
would get the same totally flat frequency response in the middle setting.<br>
<br>
<br>
<br>
--<br>
/// Neil Harper<br>
/// Every Wave is New Until it Breaks<br>
<br>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank" rel="noreferrer">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank" rel="noreferrer">marketplace@synth-diy.org</a><br>
</blockquote></div>