<div dir="ltr">My cheat sheet for this kind of thing, may be of some use to others.<div><br></div><div>Agree with the above about spectral density being an interesting measurement, I love my Rohde Schwarz UPL to death for that kind of thing</div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, 16 Mar 2021 at 17:30, Florian Teply <<a href="mailto:usenet@teply.info">usenet@teply.info</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">Hi All,<br>
<br>
Am Mon, 15 Mar 2021 23:57:28 +0000<br>
schrieb Tom Wiltshire <<a href="mailto:tom@electricdruid.net" target="_blank">tom@electricdruid.net</a>>:<br>
<br>
> Hi All,<br>
> <br>
> I’ve been reading data sheets for linear regulators, and I’ve got a<br>
> question.<br>
> <br>
> Some regulators specific the output noise voltage from 10Hz to 100KHz<br>
> as an RMS level, usually uV. However, the Microchip MCP1702 specifies<br>
> an output noise figure as 8 uV/Hz. What does this mean? What’s the<br>
> relationship between uV/Hz and RMS uV?<br>
> <br>
Ah, that noise stuff.<br>
Actually It's not that difficult once you know what you need to do with<br>
that figure in order to get something useful. The value given is noise<br>
density and reads V/sqrt(Hz). Converting to RMS is somewhat easy: <br>
Multiply the value give with the square root of the bandwidth of<br>
interest, here 100 kHz - 10 Hz which more or less equal to 100 kHz.<br>
Square root of 1e5 Hz is approximately 3e2 sqrt(Hz).<br>
8 uV / sqrt(Hz) times 300 sqrt(Hz) yields 2400 uV or 2.4 mV. It's<br>
already RMS, so comparison to Volts RMS is easy.<br>
<br>
There are pitfalls however: The simple calculation give above only<br>
gives reasonable results when the noise density is constant across<br>
the bandwith of interest (that means white noise and would exclude<br>
flicker noise). And: The datasheet states voltage noise density<br>
under specific conditions. For one thing, it doesn't say how that number<br>
changes when you divert from those conditions given. Change Capacitance<br>
or current draw and you're on your own. It also doesn't tell anything<br>
about flicker noise. Chances are it's not going to be too shabby with a<br>
1/f noise corner below 100 Hz, but you never know beforehand: the<br>
mnufacturer didn't specify either because they didn't bother to measure<br>
it (that's not super easy in automated testing as it takes quite a<br>
while to do) or because they decided it's so bad they rather not report<br>
it publicly.<br>
<br>
There's one more pitfall: some manufacturers tend to specify noise as<br>
peak-to-peak value, and conversion between peak-to-peak and RMS depends<br>
on what number the manufacturer settled for as peak-to-average ratio<br>
for noise, which usually is not given in the datasheet...<br>
<br>
HTH,<br>
Florian<br>
<br>
> Here’s the datasheet:<br>
> <br>
> <a href="https://4donline.ihs.com/images/VipMasterIC/IC/MCHP/MCHPS03366/MCHPS03366-1.pdf?hkey=6D3A4C79FDBF58556ACFDE234799DDF0" rel="noreferrer" target="_blank">https://4donline.ihs.com/images/VipMasterIC/IC/MCHP/MCHPS03366/MCHPS03366-1.pdf?hkey=6D3A4C79FDBF58556ACFDE234799DDF0</a><br>
> <br>
> Thanks for any guidance!<br>
> <br>
> Tom<br>
> <br>
> ==================<br>
>        Electric Druid<br>
> Synth & Stompbox DIY<br>
> ==================<br>
> <br>
> <br>
> <br>
> <br>
> _______________________________________________<br>
> Synth-diy mailing list<br>
> <a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
> <a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
> Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a><br>
<br>
<br>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
Selling or trading? Use <a href="mailto:marketplace@synth-diy.org" target="_blank">marketplace@synth-diy.org</a><br>
</blockquote></div>