<div><span style="color:rgb(0, 0, 0)"><span style="font-family:"Helvetica Neue", Helvetica, Arial, sans-serif"><span style="font-size:14px">>100k shows up a lot in eurorack circuits since it's the defacto input impedance.</span></span></span><br></div><div><br></div><div>Could it be that a lot of (more recent) Eurorack circuits are heavily inspired by Ray Wilson? ;-)<br></div><div><br></div><div>As to the context and design intention behind my question, in this case it's less specific, general curiosity. I'm just trying to weigh the options, for example for small circuits, or like Mattias mentioned in low-noise signal paths. <br></div><div><br></div><div>I was suspecting that input impedance plays into this, but for op-amp stages other than inputs there would be no obvious reason to use values as high as 100k unless to conserve power.<br></div><div><br></div><div><br></div><div>thanks,<br></div><div>Tom<br></div><div><br></div><div><br></div><div><br></div><div><br></div><div>‐‐‐‐‐‐‐ Original Message ‐‐‐‐‐‐‐<br></div><div> On Friday, 13. November 2020 22:48, ben gebhardt via Synth-diy <synth-diy@synth-diy.org> wrote:<br></div><div> <br></div><blockquote class="protonmail_quote" type="cite"><div style="font-family:Helvetica Neue, Helvetica, Arial, sans-serif;font-size:13px;"><div><br></div><div dir="ltr" data-setdir="false">(first time poster!)<br></div><div dir="ltr" data-setdir="false"><br></div><div dir="ltr" data-setdir="false">Hi Ian,<br></div><div dir="ltr" data-setdir="false"><br></div><div dir="ltr" data-setdir="false">Usually in my experience one would scale down resistors around an opamp to generally lower the johnson noise contribution.  Additionally there is something to be said for high impedance nodes and coupling in radiated noise from external sources but usually that's only problematic over 1M.  <br></div><div dir="ltr" data-setdir="false"><br></div><div dir="ltr" data-setdir="false"><span><span style="color:rgb(0, 0, 0)"><span style="font-family:Helvetica Neue, Helvetica, Arial, sans-serif">As to why it's commonplace, I'm not sure which schematics you are referring to, but as mentioned, 100k shows up a lot in eurorack circuits since it's the defacto input impedance.</span></span></span><br></div><div dir="ltr" data-setdir="false"><br></div><div dir="ltr" data-setdir="false">There are a ton of other factors in the decision of this resistor, it's hard to generalize rationale w/o the context of the circuit and design intentions.  Happy to comment on something more specific.<br></div><div dir="ltr" data-setdir="false"><br></div><div dir="ltr" data-setdir="false">Ben.<br></div><div><br></div></div><div class="yahoo_quoted"><div style="font-family:'Helvetica Neue', Helvetica, Arial, sans-serif;font-size:13px;color:#26282a;"><div>On Friday, November 13, 2020, 04:16:17 PM EST, Mattias Rickardsson <mr@analogue.org> wrote:<br></div><div><br></div><div><br></div><div><div><div><div><div><div><div dir="ltr">Mattias Rickardsson <<a rel="nofollow" shape="rect" target="_blank" href="mailto:mr@analogue.org">mr@analogue.org</a>> skrev:<br></div><blockquote style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex;"><div><div><div><br></div><div>And perhaps 10k-22k for TL06x.<br></div></div></div></blockquote></div></div><div><br></div><div>I should have written 22k-47k.<br></div><div><div><br></div><div>/mr<br></div><div><br></div><div><div><blockquote style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex;"><div><div><br></div></div></blockquote></div></div></div></div></div></div><div><div>_______________________________________________<br></div><div>Synth-diy mailing list<br></div><div><a shape="rect" href="mailto:Synth-diy@synth-diy.org">Synth-diy@synth-diy.org</a><br></div><div><a shape="rect" href="http://synth-diy.org/mailman/listinfo/synth-diy" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br></div><div>Selling or trading? Use <a shape="rect" href="mailto:marketplace@synth-diy.org">marketplace@synth-diy.org</a><br></div></div></div></div></div></blockquote><div><br></div>