<div dir="ltr"><div>I have also been somewhat bemused by these comments, having worked with computers my entire career and survived the capacitor plague.<br></div><div><br>Richard Devine is on record saying that he simply leaves all his modular synths turned on all the time. Perhaps...<br></div><div><br>* his synth enclosures are well ventilated<br>* he has amazing climate control<br>* all the electrolytic caps in all his modular gear are 105C / 12000 hour rated</div><div>* unicorns are casually shitting the most incredible rainbows on his front lawn<br></div><div><br></div><div>Even then... why would Panasonic et al put hour ratings on their products if they were immortal?</div><div><br></div><div>John<br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, 5 May 2020 at 21:11, Steve Lenham <<a href="mailto:steve@bendentech.co.uk">steve@bendentech.co.uk</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">On 05/05/2020 11:31, Gordonjcp wrote:<br>
> You'll never need to "recap" a power supply.  Ever.  Unless you've done something crazy and actually damaged it, of course.<br>
<br>
Sorry, but you post this over and over and it just isn't true. Saying <br>
that you never need to recap a power supply is every bit as extreme - <br>
and mistaken - as saying that you should always do it.<br>
<br>
Two real-world examples:<br>
<br>
1. I worked on some jolly expensive Apogee converter units that wouldn't <br>
turn on. They used off-the-shelf switch-mode power supply modules and <br>
didn't have a proper hard power switch, only a standby mode. This meant <br>
that the SMPS was running all the time that power was connected; the <br>
output reservoir caps in an SMPS work fairly hard and these were dead. <br>
It's a situation that is increasingly common and will cause the <br>
premature demise of a lot of gear, so Quantec IMO have the right idea.<br>
<br>
The best electrolytic caps have a rated lifetime of around 12000 hours. <br>
Yes, this is at their max rated temperature and lifetime doubles for <br>
every 10 degrees below that temp, but there are 8760 hours in a year so <br>
you cannot rely on them for too many years if in constant use.<br>
<br>
I am told that the same problem afflicts the power supplies in Mac Pro <br>
workstations, with computers costing a five-figure sum being put out of <br>
action by a handful of worn-out electrolytic caps.<br>
<br>
2. I work a lot on vintage Lexicon effects and they use late 70s/early <br>
80s tantalum caps and poor quality electrolytics. Same goes for e.g. <br>
Prophet 5s. The tants are prone to spontaneously failing short-circuit - <br>
not all of them, and not after any particular length of time, but <br>
statistically it is quite common. Presumably in your world you would <br>
wait for that to happen, then find the one bad cap and replace it - and <br>
repair all the other damage it might have done. But a lot of people - <br>
those that can't do repairs themselves, or are already having work done <br>
on their gear, or just need their kit to keep working because they rely <br>
on it - prefer to eliminate the possibility of such a failure happening <br>
any time soon by fitting better quality modern caps. It is a question of <br>
risk management.<br>
<br>
I could go on. I accept that good-quality electrolytics seeing moderate <br>
100Hz ripple in a well-ventilated piece of equipment can go on for a <br>
very long time. But those conditions arise in a diminishing number of cases.<br>
<br>
Cheers,<br>
<br>
Steve L.<br>
Benden Sound Technology<br>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
</blockquote></div>