<div dir="ltr"><div dir="ltr"><div>so I was looking on Mouser and found (Mouser) part# <span id="gmail-spnMouserPartNumFormattedForProdInfo">279-YR1B100KCC</span></div><div><br></div><div>100k 0.1% 15ppm/C 0.25W axial through-hole resistors: <span>$0.451 each in quantity >100<br></span></div></div><div dir="ltr"><div><br></div><div>I think adding a reasonably nice meter to your bench is still worth it, but on the other hand you've apparently been surviving just fine in DIY without one...<br></div><div><br></div><div>John<label class="gmail-mpart-number-lbl"><br><br></label></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, 21 Jan 2020 at 17:56, David G Dixon <<a href="mailto:dixon@mail.ubc.ca">dixon@mail.ubc.ca</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">Thanks to all for your responses.  However, I ended up solving my problem.<br>
I was making a 1V/oct switching ladder and decided to use 100k resistors.<br>
Most of them were slightly less than that, and my meter was reading only<br>
three digits.  I picked 7 resistors all 99.6k and built the ladder, and the<br>
results were less than stellar.  So, I thought, maybe I'll use 10k<br>
resistors, but then I was still only getting 3 digits.<br>
<br>
Then I had the bright idea of trying 30k resistors.  These gave me four<br>
digits, so I was able to find 7 resistors which were exactly 30.16k, and the<br>
results were much better.  Now each voltage is within 1 or 2 mV of the<br>
target.  I don't understand why it isn't more perfect, but I can live with<br>
it.<br>
<br>
So, long story short, I'm not gonna buy a new multimeter.<br>
<br>
<br>
<br>
-----Original Message-----<br>
From: Synth-diy [mailto:<a href="mailto:synth-diy-bounces@synth-diy.org" target="_blank">synth-diy-bounces@synth-diy.org</a>] On Behalf Of David<br>
G Dixon<br>
Sent: Monday, January 20, 2020 4:14 PM<br>
To: 'Synth DIY'<br>
Subject: [sdiy] Looking for a multimeter<br>
<br>
Hello SDIY Team,<br>
<br>
I'm looking for a multimeter that, when reading a resistor just a bit less<br>
than 10k, will give me a reading like:<br>
<br>
9.972 k<br>
<br>
Instead of the more common:<br>
<br>
9.97 k<br>
<br>
Also, I don't want to spend more than about $200 (I know I can get a Fluke<br>
for $500, but this is freaking ridiculous and highway robbery -- I just want<br>
one more digit than my $25 Victor 925A is giving me -- it doesn't need to<br>
work underwater or survive nuclear holocaust).<br>
<br>
Any suggestions?<br>
<br>
Thanks in advance!<br>
Dave Dixon<br>
<br>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
<br>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
</blockquote></div></div>