<div dir="ltr">thats an interesting idea - it might be good to test these things in the digital domain (max, PD, supercollider etc) before committing to a build, especially if what you need ends up being more complex.</div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">fim., 5. des. 2019 kl. 11:16 skrifaði Florian Anwander <<a href="mailto:fanwander@mnet-online.de">fanwander@mnet-online.de</a>>:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">
  
    
  
  <div>
    <p>Hi Jean<br>
    </p>
    <div>Am 04.12.19 um 17:31 schrieb Jean
      Bender:<br>
    </div>
    <blockquote type="cite">
      <pre>discovered that most of them was pretty good for following musical
instruments signals, but not so much for more electronic audio
signal..
I mean, i play a lot of ambient and noise stuff, including sounds
without so much attack, even if they have some relief.

And that's my point :  i'd like to build myself an enveloppe follower
able to be really subtle, and able to be effective even on droning
sounds...
So where should i take a look ? What i have to be careful of ?</pre>
    </blockquote>
    <p>Brian wrote all the theory already.</p>
    <p>Your main problem is: drones typically don't have a significant
      change in amplitude. On the other side: drones often change the
      colour of sound, the spectrum.</p>
    <p>So I think you don't need a simple envelope-Follower, but you
      might need something more complex. I could imagine something like
      the analysis section of a vocoder, with an circuit after it, that
      outputs a voltage that corresponds to the frequency range or
      frequency weight.</p>
    <p><br>
    </p>
    <p>I did not think it completely over, but a first attempt might
      look like this:</p>
    <p>A state-variable-filter splits the signal in two signals: high
      and low. Both signals then are fed through an  envelope follower
      each. Now the output voltages of the two env-followers are
      subtracted. The result would be something like:</p>
    <ul>
      <li>full frequency-spectrum = 0V</li>
      <li>only high frequencies = +maxV</li>
      <li>only low frequencies = -maxV</li>
    </ul>
    <p>I am not sure, whether the result is really interesting or
      usable, but it might be worth a try.</p>
    <p><br>
    </p>
    <p>Florian<br>
    </p>
  </div>

_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
</blockquote></div><br clear="all"><div><br></div>-- <br><div dir="ltr" class="gmail_signature"><div dir="ltr"><div>•</div><div><a href="http://ulfurhansson.com/" style="color:rgb(17,85,204)" target="_blank">ulfurhansson.com</a></div><div><a href="http://cargocollective.com/ulfur" style="color:rgb(17,85,204)" target="_blank">cargocollective.com/ulfur</a></div><div><a href="http://instagram.com/ulfur_" style="color:rgb(17,85,204)" target="_blank">instagram.com/ulfur_</a></div></div></div>