<div dir="ltr"><div>I just did one recently. I started by looking at other schematics, but ended up designing my own. Here is a basic overview of the circuit.</div><div><br></div><div>1. Use a diode to only allow positive signals through.</div><div>2. Use a reversed diode to only allow negative signals through.</div><div>3. Use an inverting opamp to invert the negative signal (it will become positive).</div><div>4. Mix the two signals together.</div><div>5. Filter the signals with an active filter (play with the caps value until it sounds right and doesn't have the source signal coming through).</div><div>6. Use an opamp if you need to amplify the output.</div><div><br></div><br clear="all"><div><div dir="ltr" data-smartmail="gmail_signature"><div dir="ltr"><div dir="ltr"><font face="verdana, sans-serif" color="#444444"><b>Jacob Watters</b></font></div></div></div></div><br></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Wed, Dec 4, 2019 at 11:32 AM Jean Bender <<a href="mailto:lofideadbeat@gmail.com" target="_blank">lofideadbeat@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">Hi again.<br>
Well, i should be more precise :  Since i'm in eurorack, i had a lot<br>
of different envelope followers, mainly as inputs for my system. I<br>
discovered that most of them was pretty good for following musical<br>
instruments signals, but not so much for more electronic audio<br>
signal..<br>
I mean, i play a lot of ambient and noise stuff, including sounds<br>
without so much attack, even if they have some relief.<br>
<br>
And that's my point :  i'd like to build myself an enveloppe follower<br>
able to be really subtle, and able to be effective even on droning<br>
sounds...<br>
So where should i take a look ? What i have to be careful of ?<br>
<br>
Thanks !!<br>
J.<br>
<br>
Le mer. 4 déc. 2019 à 16:44, Jean Bender <<a href="mailto:lofideadbeat@gmail.com" target="_blank">lofideadbeat@gmail.com</a>> a écrit :<br>
><br>
> Hi folks !<br>
><br>
> Well, i know i could just pick up any schematic i can find on the net<br>
> for building myself an enveloppe follower as many exist actually, but<br>
> i would rather really understand how it works so..<br>
><br>
> I would be happy to grab any advice, text, info, history about the way<br>
> they are built.<br>
> Also if you have schematics you find useful, or because they offer<br>
> specific way of building a such module..<br>
><br>
> I would be really happy.<br>
><br>
> Thanks per advance<br>
> Best<br>
> J.<br>
<br>
<br>
<br>
-- <br>
Jean Bender<br>
<br>
Hak Lofi Record<br>
<br>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
</blockquote></div>