<div dir="ltr">Apart from ripple, a small problem I have found with DC/DC converters is that there is a maximum capacitive load. Correct me if I am wrong but I think what tends to happen is it trips the short circuit protection when the module is powering up because of the inrush current. I have seen them get stuck in a hiccup like loop (this was in a non synth project with a lot of caps!). Could be an issue if you are powering a lot of mixed modules in a modular. For example the <span class="gmail-im">ECLB40W-24D12 has ma</span>ximum 1650μF load, that's quite generous, but its a spec to watch out for. <br></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Fri, 8 Nov 2019 at 11:55, mark verbos <<a href="mailto:markverbos@gmail.com">markverbos@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">I put a regulator diode on the input side, to protect against reverse voltage frying it, but I’m not sure if that is necessary. The “15 VDC” comes in on a 2.1mm barrel connector from an external brick. It goes through a switch, a diode and a cap to ground before the DC-DC converter. The advantage is that it is 90% efficient, weighs less, can be plugged in anywhere in the world without a converter, doesn’t get hot, hardly takes up any space, maybe more….<br>
<br>
I had to replace the transformer in a TR-909 this year because someone plugged a Japanese one into a European outlet. Inside, it’s just a jumper to change it, but the owner didn’t know that. It makes me wonder if replacing the transformer with a SMPS would be a better solution. I didn’t, but I wonder.<br>
<br>
Mark<br>
<br>
<br>
<br>
<br>
<br>
> On Nov 8, 2019, at 6:00 AM, Michael Zacherl <<a href="mailto:sdiy-mz01@blauwurf.info" target="_blank">sdiy-mz01@blauwurf.info</a>> wrote:<br>
> <br>
> <br>
>> On 7 Nov 2019, at 12:51, mark verbos <<a href="mailto:markverbos@gmail.com" target="_blank">markverbos@gmail.com</a>> wrote:<br>
>> <br>
>> I use the ECLB40W-24D12 which is a 40W metal can one. It will take pretty much any DC you throw at it (9V-36V per the datasheet). I put some big caps to ground on the output of them.<br>
> <br>
> <br>
> Hi Mark, so, how does your input side look like? <br>
> ATM that implementation appears like the (aforementioned) hybrid version to me where I can’t really see its advantage over a linear PSU. Only reason, maybe, I can’t find a +/- SMPSU using mains voltage?<br>
> m.<br>
> _______________________________________________<br>
> Synth-diy mailing list<br>
> <a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
> <a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
<br>
<br>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
</blockquote></div>