<div dir="ltr"><div>Keeping in mind that were talking about the Control amp portion of Mike's VCA technique not the audio path.</div><div><br></div><div></div><div>100k is, by modular synth tradition, the expected load a driving module would see. <br></div><div>This is due to the many inputs a control module could commonly be expected to drive.</div><div></div><div><br></div><div>The audio path using 30k input is of course not-traditional but might be excused as the audio input of a VCA is most often a single driving source.</div><div> <br></div><div>Bandwidth reduction resulting from the 100pF feedback capacitance has no practical impact for the usual VCA Control sources and stabilizes the loop (with it's dynamic gain element) across all 3 possible chip alternatives. Any increased noise level in the control path pales when considered against the dynamic range of the technique which is restricted by the op-amp selected.</div><div><br></div><div>regards,</div><div>p</div><div><br></div><div></div><div><br></div><div> <br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Fri, Feb 15, 2019 at 4:18 AM Mattias Rickardsson <<a href="mailto:mr@analogue.org">mr@analogue.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="ltr"><div dir="ltr">On Thu, 14 Feb 2019 at 22:10, David G Dixon <<a href="mailto:dixon@mail.ubc.ca" target="_blank">dixon@mail.ubc.ca</a>> wrote:<br></div><div class="gmail_quote"><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><u></u>



<div>
<div dir="ltr" align="left"><span class="gmail-m_-3482944908337638808gmail-m_816852409983698721280031021-14022019"><font size="2" face="Arial" color="#0000ff">Increasing the resistors from 30k to 100k also fixed the 
problem, with the same 22pF cap in place.</font></span></div></div></blockquote><div><br></div><div>FWIW, 100k gives higher noise floor than 30k - but improves the THD a bit.</div><div><br></div><div>Depending on the design, the "right" choice could be either one.</div><div><br></div><div>/mr</div><div><br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div><blockquote style="border-left:2px solid rgb(0,0,255);padding-left:5px;margin-left:5px;margin-right:0px" dir="ltr"><div dir="auto">
  <div dir="auto">
  <div class="gmail_quote">
  <blockquote style="border-left:1px solid rgb(204,204,204);margin:0px 0px 0px 0.8ex;padding-left:1ex" class="gmail_quote"></blockquote></div></div></div></blockquote></div>
</blockquote></div></div>
_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
</blockquote></div>