<div dir="ltr"><div><br></div><div>Joel </div><div><br></div>I've had problems with mini DIN connectors not mating properly, and it turned out the outside diameter of plastic cover on rewirable mini DIN plugs is too large and won't fit into the socket recess, so the pins won't reach right into the socket.  I've had to trim some plastic off the DIN plug cover to make them fit.<div><br></div><div>An alternative solution would be to buy a molded mini DIN cable, cut it in two and wire the bare end into a small plastic box with four RCA/phono connectors (or jacks if you prefer) on it.</div><div><br></div><div><br></div><div>Steve  <div><br></div><div><br></div><div><br></div></div></div><br><div class="gmail_quote"><div dir="ltr">On Mon, 31 Dec 2018 at 06:39, Joel B <<a href="mailto:onephatcat@earthlink.net">onephatcat@earthlink.net</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="auto"><div dir="ltr"><span></span></div><div dir="ltr"><div dir="ltr"><span></span></div><div dir="ltr">I have a couple of Pearl fightman analog drum modules (circa 1979/80) and one came with the complete drum kit and cables, the other without.<div><br></div><div> I’ve been attempting to create a second set of cables, with only partial success. The cables are each a 5 pin mini-din (<a href="https://goo.gl/images/pDHvsP" target="_blank">https://goo.gl/images/pDHvsP</a>) that split to a fan of 4 and 5 RCA Male jacks - proprietary cables that nobody seems to make. (crash/ride/oh/ch)/(kick/snare/toms). First problem is how to solder tiny wires to tiny posts. Took a while to get that right, and I’m pretty sure there is a better way, like wires with some kind of clip already attached...<div><br></div><div>Second problem was that I think the outside ring on the mini-din is the ground (or at least the “common” wire) as far as I can tell from my amature multimetering. </div><div><br></div><div>So I built a couple cables, and the second try sort of worked but a little intermittently. Thinking I understood how to do this now I built a third one that works even less and a fourth one that doesn’t work at all. I can’t find a short. The pins all have good connectivity. </div><div><br></div><div>I was trying to adapt to 3.5mm jacks so I wired to 3.5mm female sockets instead of RCA male, to use with beatstep pro or other trigger <span style="background-color:rgba(255,255,255,0)">(Original cables with an rca/3.5mm adapter do work with beatstep pro). </span>I could only find TRS 3.5mm sockets online when I wanted TS but I’m pretty sure I soldered that part the same way on all my attempts... </div><div><br><div dir="ltr"><span style="background-color:rgba(255,255,255,0)">I’m wondering, are the pins on the newer mini-din male just maybe not long enough? What am I doing wrong? Certainly they seem not designed for the sleeve of the mini-din to be a soldier point but It seems to be so in the original cables, so I made that connection.</span></div></div><div dir="ltr"><span style="background-color:rgba(255,255,255,0)"><br></span></div><div dir="ltr"><span style="background-color:rgba(255,255,255,0)">Joel</span></div></div></div></div></div>_______________________________________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
</blockquote></div>