<div dir="ltr">This is what I was going to suggest.<br><br>These cliff jacks have a switch on sleeve as well as on tip.  If I take that switch and run it to my "selector" with a pull up, I have zero when there's no plug, and whatever the pull up value is when there is a plug.<br><br>This is the jack I'm using, a clone of the 1384: <a href="http://www.smallbear-electronics.mybigcommerce.com/search.php?search_query=0632&x=0&y=0">http://www.smallbear-electronics.mybigcommerce.com/search.php?search_query=0632&x=0&y=0</a><div><br></div><div>My solution for the right-angle issue was to have a small side-board with these jacks on them that has a right-angle header soldered to the main panel PCB.  I suppose flying wires would do as well.</div><div><br></div><div><a href="https://photos.app.goo.gl/QNCZAmeZifASeyd69">https://photos.app.goo.gl/QNCZAmeZifASeyd69</a><br></div><div><br></div><div>Yes, that's bodged a bit -- originally I was going to do stereo, but I had the monos on hand and realized I could use the sleeve switch, and use a cheaper jack.  That's what prototypes are for, right? :)</div><div><br></div><div>I didn't think the stereo thonkiconn was switched, which made it unsuitable for my purposes.</div><div><br></div><div><br></div><div>Pete</div><div><br></div><div><br></div><div><br><div class="gmail_extra"><br><div class="gmail_quote">On Tue, Jul 24, 2018 at 2:21 AM, Matthias Herrmann <span dir="ltr"><<a href="mailto:matthias.herrmann@fonik.de" target="_blank">matthias.herrmann@fonik.de</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">The classic Cliff socket CL1384 as used on the older Doepfer modules has both<br>
contacts switched. It is not a right-angle mounted socket though. There are a<br>
lot of these other cheap alibaba sockets with both contatacts switched.<br>
<br>
The problem seems to be to find a right angle mounted socket?<br>
<br>
If you are looking for right angle sockets, the Thonkiconn is now available in<br>
stereo, too (PJ366ST). they have the same height as the mono thonkiconn<br>
(PJ398SM).<br>
<br>
Cheers,<br>
Matthias<br>
<div class="gmail-m_9127158028474023200HOEnZb"><div class="gmail-m_9127158028474023200h5"><br>
<br>
<br>
> On 2018-07-23 14:21 -0700, Tim Ressel wrote:<br>
> <br>
> > I've got another challenge: how to detect when a plug is<br>
> > inserted into a jack. These are 3.5mm mono jacks btw. The<br>
> > current method is to use a stereo jack. When a mono plug is<br>
> > inserted the ring connection gets shorted to ground by the<br>
> > sleeve of the plug. This method works well, but the stereo<br>
> > jacks are taller than the mono jacks.<br>
> ><br>
> > The only jack I can use is a switched mono jack where switched<br>
> > port is tied to the tip port until a plug is inserted. My idea<br>
> > is to use the switch port to feed an out of range voltage to<br>
> > the tip port, probably a negative voltage. Then use a<br>
> > comparator to detect when the tip port goes high.<br>
> <br>
> Just in case you don't already know, there are phone jacks with<br>
> isolated switch circuits. Switchcraft 113EX and 113X, for<br>
> example :<br>
> <br>
>   <a href="http://switchcraft.com/Drawings/110x-m110x_series_cd.pdf" rel="noreferrer" target="_blank">http://switchcraft.com/Drawin<wbr>gs/110x-m110x_series_cd.pdf</a><br>
> <br>
> I've seen 3.5 mm sockets with suspiciously high number of pins<br>
> so something similar may exist in that size.<br>
> <br>
> --<br>
> André Majorel <a href="http://www.teaser.fr/~amajorel/" rel="noreferrer" target="_blank">http://www.teaser.fr/~amajorel<wbr>/</a><br>
<br>
<br>
<br>
______________________________<wbr>_________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/l<wbr>istinfo/synth-diy</a><br>
</div></div></blockquote></div><br></div></div></div>