<div dir="auto">No no, separate input resistors and RC snubber networks for the two VCAs, so you know what current each virtual-ground input pin gets - and then summing their output current into one common op-amp just as you said.<div dir="auto"><br></div><div dir="auto">30k for the Rin maxes out the input current capability for SSM2164/V2164 within +/-15 V supplies; with lower supplies you can handle lower input resistances, and the SSI2164 even lower to reach lower noise.<br><div dir="auto"><br></div><div dir="auto">/mr</div><div dir="auto"><br></div></div></div><br><div class="gmail_quote"><div dir="ltr">Den sön 17 juni 2018 22:31Tom Wiltshire <<a href="mailto:tom@electricdruid.net">tom@electricdruid.net</a>> skrev:<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">I don’t think it’s any extra C and Rs at all. Like Ian said, thew them together pin for pin. I don’t see the point of hanging two RC networks off one combined input, so there’s nothing extra there. I suppose you could use separate 30K input resistors and RC networks for the two inputs, but why?<br>
<br>
We know from the datasheet that the outputs can be tied together, so there’s no problem there.<br>
<br>
Control input impedance is a reasonable point - the 5K impedance isn’t high to start with, and will get lower, but it’s still at a manageable level. So I don’t see a problem there either.<br>
<br>
Tom<br>
<br>
> On 17 Jun 2018, at 15:28, Mattias Rickardsson <<a href="mailto:mr@analogue.org" target="_blank" rel="noreferrer">mr@analogue.org</a>> wrote:<br>
> <br>
> Definitely, use them in parallel. The VCAs are easily the noisiest bottlenecks of your circuits and using two in parallel should lower it around 3 dB.<br>
> <br>
> I don't see how it wouldn't be worth the circuitry - what is it, an additional C and two additional R?<br>
> <br>
> Also, make sure to use the new improved SSI2164 for even better SNR and/or THD potential.<br>
> <br>
> /mr<br>
> <br>
> On Sun, 17 Jun 2018 at 13:49, Tom Wiltshire <<a href="mailto:tom@electricdruid.net" target="_blank" rel="noreferrer">tom@electricdruid.net</a>> wrote:<br>
> Hi all,<br>
> <br>
> A quick query, if I may: Is there any noise advantage to using two 2164 VCAs in parallel?<br>
> <br>
> I’ve got a circuit that uses two VCAs, so there are two others spare on the chip. And then it occurred to me that there might be a minor gain by using them in parallel pairs. It’s a case of “well, they’re there so we might as well use them” if there’s no reason not to.<br>
>  Or would it be better to simply disable the unused sections?<br>
> <br>
> Thanks,<br>
> Tom<br>
> <br>
> ==================<br>
>        Electric Druid<br>
> Synth & Stompbox DIY<br>
> ==================<br>
> <br>
> <br>
> _______________________________________________<br>
> Synth-diy mailing list<br>
> <a href="mailto:Synth-diy@synth-diy.org" target="_blank" rel="noreferrer">Synth-diy@synth-diy.org</a><br>
> <a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer noreferrer" target="_blank">http://synth-diy.org/mailman/listinfo/synth-diy</a><br>
<br>
</blockquote></div>