<div dir="ltr">Thanks to Tim for bringing this up and everyone's advice on the input bias current of the 5532. <div><br></div><div>This most likely explains a similar issue I couldn't figure out on a handful of filters I made 10+ years ago using vintage LM301s as integrators, probably near or over max spec for input bias current. Some would fail after being in use for a while by drifting to the positive rail. Hadn't thought of that in ages and at the time didn't know enough to figure that out - in retrospect this makes sense. </div><div><br></div><div>AD note MT-038 deals with input bias current: <a href="http://www.analog.com/media/en/training-seminars/tutorials/MT-038.pdf">http://www.analog.com/media/en/training-seminars/tutorials/MT-038.pdf</a><br></div><div><br></div><div>Nathan</div></div><div class="gmail_extra"><br><div class="gmail_quote">On Sat, Jan 27, 2018 at 6:34 PM, Neil Johnson <span dir="ltr"><<a href="mailto:neil.johnson71@gmail.com" target="_blank">neil.johnson71@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Tim,<br>
<br>
Don't use NE5532 for the integrators (U3).  The input bias current<br>
will integrate over time and push the integrator opamps to the<br>
positive rail.  This will happen once the gain of the 2164s is low<br>
enough that the bias current dominates.  Switch to TL072 in that<br>
position.  I would also suggest a TL072 for the other op-amp as with<br>
the resistor values you're using and taking worst-case bias current<br>
you could be seeing 10s of mV (especially U2A).<br>
<br>
Also I wouldn't recommend putting the zeners across the integrator capacitor.<br>
<br>
Neil<br>
<div class="HOEnZb"><div class="h5"><br>
<br>
On 27 January 2018 at 16:28, Tim Ressel <<a href="mailto:timr@circuitabbey.com">timr@circuitabbey.com</a>> wrote:<br>
> Hi,<br>
><br>
> Filters can be a pain. I've got one that is misbehaving. Here is a link to<br>
> the schematic:<br>
><br>
> <a href="https://www.dropbox.com/s/acjvwb17nmuok1n/PrismFilter.pdf?dl=0" rel="noreferrer" target="_blank">https://www.dropbox.com/s/<wbr>acjvwb17nmuok1n/PrismFilter.<wbr>pdf?dl=0</a><br>
><br>
> At low CVs it filters fine, but as the freq cv hits around 2 volts the<br>
> behavior gets odd. I start seeing a rising DC bias on all the outputs. At<br>
> about 3 volts all the outputs rail positive.<br>
><br>
> Any help is appreciated. Thanks for playing!<br>
><br>
> --<br>
> --Tim Ressel<br>
> Circuit Abbey<br>
> <a href="mailto:timr@circuitabbey.com">timr@circuitabbey.com</a><br>
><br>
> ______________________________<wbr>_________________<br>
> Synth-diy mailing list<br>
> <a href="mailto:Synth-diy@synth-diy.org">Synth-diy@synth-diy.org</a><br>
> <a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/<wbr>listinfo/synth-diy</a><br>
<br>
<br>
<br>
</div></div><span class="HOEnZb"><font color="#888888">--<br>
<a href="http://www.njohnson.co.uk" rel="noreferrer" target="_blank">http://www.njohnson.co.uk</a><br>
</font></span><div class="HOEnZb"><div class="h5">______________________________<wbr>_________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/<wbr>listinfo/synth-diy</a><br>
</div></div></blockquote></div><br></div>