<div dir="auto">Tim,<div dir="auto"><br></div><div dir="auto">I think whatever you're going to end up with is two opamps unless you can do the inversion somewhere else in the CV path.</div><div dir="auto"><br></div><div dir="auto">Neil</div><div dir="auto"><br></div></div><div class="gmail_extra"><br><div class="gmail_quote">On 25 Aug 2017 22:52, "Tim Ressel" <<a href="mailto:timr@circuitabbey.com">timr@circuitabbey.com</a>> wrote:<br type="attribution"><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Nice idea, but I don't have that available. The problem is the VCA stage as shown inverts. Not usually an issue for audio but I am using it as a dc vca for control voltages.<br>
<br>
--tr<br>
<br>
<br>
<br>
On 8/25/2017 1:02 PM, Tom Wiltshire wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
The best way to save an op-amp in this situation is to feed the output into another current input, like another 2164 VCA, or a subsequent mixer stage (no need to go VCA->I2V->mixer) or etc etc<br>
It’s a change in thinking from voltage to current, but it works just the same!<br>
<br>
HTH,<br>
Tom<br>
<br>
==================<br>
        Electric Druid<br>
Synth & Stompbox DIY<br>
==================<br>
<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
On 25 Aug 2017, at 19:37, Tim Ressel <<a href="mailto:timr@circuitabbey.com" target="_blank">timr@circuitabbey.com</a>> wrote:<br>
<br>
Hi,<br>
<br>
So the datasheet for the 2164 shows the output always routed to an inverting opamp configured as a current to voltage convertor. Is it possible to configure the 2164 output with a resistor to ground and a non-inverting opamp buffer? I am trying to have an opamp package.<br>
<br>
Thanks!<br>
<br>
<br>
-- <br>
--Tim Ressel<br>
Circuit Abbey<br>
<a href="mailto:timr@circuitabbey.com" target="_blank">timr@circuitabbey.com</a><br>
<br>
______________________________<wbr>_________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/l<wbr>istinfo/synth-diy</a><br>
</blockquote>
<br>
</blockquote>
<br>
-- <br>
--Tim Ressel<br>
Circuit Abbey<br>
<a href="mailto:timr@circuitabbey.com" target="_blank">timr@circuitabbey.com</a><br>
<br>
______________________________<wbr>_________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org" target="_blank">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/l<wbr>istinfo/synth-diy</a><br>
</blockquote></div></div>