<div dir="ltr">right on</div><div class="gmail_extra"><br><div class="gmail_quote">On Tue, Jul 18, 2017 at 6:10 PM,  <span dir="ltr"><<a href="mailto:rsdio@audiobanshee.com" target="_blank">rsdio@audiobanshee.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Sure, it's not that hard. I have soldering tweezers for SMD resistors, capacitors, and even ICs up to 14-pin. But at a certain point you reach diminishing returns. There is time and money invested, and I'd rather save my time and money for things that I cannot pay someone else to do. I make a whole lot more progress towards my electronics goals by avoiding 99% of SMD work.<br>
<br>
I will admit that it's good to spend some amount of time honing the skills. I recently designed a board with an optional op-amp that ended up performing worse than a straight connection. Fortunately, I design the PCB with traces for a SMD jumper so I could remove the op-amp and still connect the signal directly. I did that rework myself, because removing an 8-pin SMD and adding a two-conductor 0-Ohm resistor was a cinch. So, there's a balance between doing a lot of manual SMD versus just hitting a couple of parts for a quick mod.<br>
<br>
Brian<br>
<div class="HOEnZb"><div class="h5"><br>
<br>
On Jul 18, 2017, at 3:57 PM, Quincas Moreira <<a href="mailto:quincas@gmail.com">quincas@gmail.com</a>> wrote:<br>
> Oh, c'mon it's not that hard, just takes some getting used to! I've only done the Ornament and Crime so far, but I'm looking forward to more :)<br>
><br>
> On Tue, Jul 18, 2017 at 5:17 PM, <<a href="mailto:rsdio@audiobanshee.com">rsdio@audiobanshee.com</a>> wrote:<br>
>> Same here. I just pay shops like Printed Circuits Assembly Corp. or Schippers & Crew to do SMD work. They have all the tools, microscopes, and experience. PCA will also do rework, which I take advantage of when replacing a component with more than two leads.<br>
>><br>
>> I realize that not every city has multiple assembly shops, and some don't even have one, but these services are becoming available remotely. Advanced Circuits (4PCB.com) offer services where they'll make the PCB and stuff the parts for you. Not sure about the prices there, but it's got to be cheaper than buying the tools yourself and losing money every time you make a mistake. It's probably a bit difficult to get a kit made, but it's worth requesting a quote.<br>
>><br>
>> I once needed a pull-up resistor added to a 144-pin DSP, and PCA asked if they could use any size resistor. I agreed, and when it came back, the flying wire and resistor were so small (0201) that I couldn't see them. Saved me from spinning the board for that one change, and also saved me from the risk of ruining one of only two prototypes that I had.<br>
>><br>
>> Brian<br>
>><br>
>> On Jul 18, 2017, at 2:23 PM, David G Dixon <<a href="mailto:dixon@mail.ubc.ca">dixon@mail.ubc.ca</a>> wrote:<br>
>> > This post sums up why I simply will not do SMD by hand.  Not... worth... the... frustration.<br>
>> ><br>
>> > From: Synth-diy On Behalf Of Elain Klopke<br>
>> > Sent: Tuesday, July 18, 2017 12:16 AM<br>
>> > To: *SYNTH DIY<br>
>> > Subject: [sdiy] Need help with a SMD kit (OT?)<br>
>> ><br>
>> > Hey list,<br>
>> ><br>
>> > I bought the Elements diy kit from Synthcube and managed to get all the surface mount components attached using solder paste, a tiny syringe, and a hot plate. Everything melted nicely and I only burnt the solder mask a bit because I wasn't quick enough getting it off the hot plate, but the copper traces appear to be still attached to the board so I'm not too worried.<br>
>> ><br>
>> > And then the problems started. I let the board cool down and then started going about eliminating solder bridges on a couple of the ICs. I cleaned up one side of the microcontroller and then made the other three worse. I got one chip that was a little crooked seated properly and then another popped free and I couldn't get it resoldered.<br>
>> ><br>
>> > I've stepped away from the kit so I don't do more damage or throw it against the wall in frustration.<br>
>> ><br>
>> > Is there anyone experienced in surface mount soldering (preferably in the US) that would be willing to fix this mess for me. I'm way out of my depth and am willing to pay postage both ways and a fee for your time.<br>
>> ><br>
>> > Thanks in advance.<br>
>> ><br>
<br>
______________________________<wbr>_________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/<wbr>listinfo/synth-diy</a><br>
</div></div></blockquote></div><br><br clear="all"><div><br></div>-- <br><div class="gmail_signature" data-smartmail="gmail_signature">Quincas Moreira<br>Test Pilot at VBrazil Modular</div>
</div>