<div dir="ltr">Oh, c'mon it's not that hard, just takes some getting used to! I've only done the Ornament and Crime so far, but I'm looking forward to more :)</div><div class="gmail_extra"><br><div class="gmail_quote">On Tue, Jul 18, 2017 at 5:17 PM,  <span dir="ltr"><<a href="mailto:rsdio@audiobanshee.com" target="_blank">rsdio@audiobanshee.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Same here. I just pay shops like Printed Circuits Assembly Corp. or Schippers & Crew to do SMD work. They have all the tools, microscopes, and experience. PCA will also do rework, which I take advantage of when replacing a component with more than two leads.<br>
<br>
I realize that not every city has multiple assembly shops, and some don't even have one, but these services are becoming available remotely. Advanced Circuits (4PCB.com) offer services where they'll make the PCB and stuff the parts for you. Not sure about the prices there, but it's got to be cheaper than buying the tools yourself and losing money every time you make a mistake. It's probably a bit difficult to get a kit made, but it's worth requesting a quote.<br>
<br>
I once needed a pull-up resistor added to a 144-pin DSP, and PCA asked if they could use any size resistor. I agreed, and when it came back, the flying wire and resistor were so small (0201) that I couldn't see them. Saved me from spinning the board for that one change, and also saved me from the risk of ruining one of only two prototypes that I had.<br>
<br>
Brian<br>
<span class=""><br>
<br>
On Jul 18, 2017, at 2:23 PM, David G Dixon <<a href="mailto:dixon@mail.ubc.ca">dixon@mail.ubc.ca</a>> wrote:<br>
> This post sums up why I simply will not do SMD by hand.  Not... worth... the... frustration.<br>
><br>
</span>> From: Synth-diy On Behalf Of Elain Klopke<br>
<span class="im HOEnZb">> Sent: Tuesday, July 18, 2017 12:16 AM<br>
> To: *SYNTH DIY<br>
> Subject: [sdiy] Need help with a SMD kit (OT?)<br>
><br>
> Hey list,<br>
><br>
> I bought the Elements diy kit from Synthcube and managed to get all the surface mount components attached using solder paste, a tiny syringe, and a hot plate. Everything melted nicely and I only burnt the solder mask a bit because I wasn't quick enough getting it off the hot plate, but the copper traces appear to be still attached to the board so I'm not too worried.<br>
><br>
> And then the problems started. I let the board cool down and then started going about eliminating solder bridges on a couple of the ICs. I cleaned up one side of the microcontroller and then made the other three worse. I got one chip that was a little crooked seated properly and then another popped free and I couldn't get it resoldered.<br>
><br>
> I've stepped away from the kit so I don't do more damage or throw it against the wall in frustration.<br>
><br>
> Is there anyone experienced in surface mount soldering (preferably in the US) that would be willing to fix this mess for me. I'm way out of my depth and am willing to pay postage both ways and a fee for your time.<br>
><br>
> Thanks in advance.<br>
><br>
<br>
</span><div class="HOEnZb"><div class="h5">______________________________<wbr>_________________<br>
Synth-diy mailing list<br>
<a href="mailto:Synth-diy@synth-diy.org">Synth-diy@synth-diy.org</a><br>
<a href="http://synth-diy.org/mailman/listinfo/synth-diy" rel="noreferrer" target="_blank">http://synth-diy.org/mailman/<wbr>listinfo/synth-diy</a><br>
</div></div></blockquote></div><br><br clear="all"><div><br></div>-- <br><div class="gmail_signature" data-smartmail="gmail_signature">Quincas Moreira<br>Test Pilot at VBrazil Modular</div>
</div>